Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
Cermet / Coated Carbide / Carbide
(mm) Descriptio A (mm)
Descriptio A T d T d
TC_0601_ 3.97 1.59 - 7
60° Triangle Positive with Hole TC_0802_ 4.76 2.38 2.3 7 TC_1102_ 6.35 2.38 2.8 7
TC_0902_ 5.56 2.38 2.5 7
TC_1103_ 6.35 3.18 2.8 7
TC_16T3_ 9.525 3.97 4.4 7
60 P Free-Cutting Steel B
Classification of usage
M Positive
Carbon steel / Alloy steel Insert
K : Interruption / 1st Choice
C
A dN Stainless Steel D
: Interruption / 2nd Choice R
TN6010S S
TN6020 Gray Cast Iron
T H : Light Interruption / 1st Choice
TN60
PV7005 Nodular Cast Iron
PV7010 : Light Interruption / 2nd Choice
PV7025
CA5505 Non-ferrous Metals
CA5515 : Continuous / 1st Choice
CA5525
CA5535 Heat-Resistant Alloys
CA6515 : Continuous / 2nd Choice
CA6525
CA4505 Titanium Alloy
CA4515 (In case hardness is under 45HRC)
PR930
PR1005 Hard materials
PR1025
PR1125Dim.CermetMEGACOATCVD CoatedPVD CoatedMEGACOATCarbide
PR1225(mm)CermetCarbideCarbide
PR1305 Applicable
Insert Description PR1310r Chipbreaker Range
PR1325
Handed insert TBGT 060102CF KW10 (ap indicates radius)
shows L-Hand SW05
Ref. Page for
Toolholder
T
0.2
Minute ap TBGT 060101M-CF < 0.1 (mm) ( Steel / Edge Length=06 ) V
060102M-CF < 0.2 0.4 W
0.3
Sharp Edge Insert (Turning)
ap 0.2
0.1 CF
Minute ap TBGT 060101MP-CF < 0.1
060102MP-CF < 0.2
0.05 0.1 0.15 0.2
Sharp Edge / Polished f (mm / rev)
Finishing TBMT 060102DP 0.2 F43 (mm) ( Steel / Edge Length=06 )
060104DP 0.4 F45 2
F48
TBGT 0601003 0.03 1.5
060101 0.1
060102 0.2 ap 1
060104 0.4
Finishing DP Without Indication
TBGT 0601005M < 0.05 0.5
060101M < 0.1
060102M < 0.2 0.05 0.1 0.15 0.2
060104M < 0.4 f (mm / rev)
Cast Iron TBGW 060102 0.2 (mm)
060104 0.4 4 ( Steel / Edge Length=08,09,11)
U 11
Without Chipbreaker 0.2 ap 3
0.4 U 08
Finishing-Medium TCMT 090202HQ 0.2 F41 2
090204HQ 0.4 HQ
0.8 1
TCMT 110202HQ
110204HQ 0.1 0.2 0.3 0.4
110208HQ f (mm / rev)
TCMT 16T304HQ 0.4 -
16T308HQ 0.8
16T312HQ 1.2
TCGT 0802003F -U 0.03 ap (mm)
080201F -U 0.1 4 ( Steel / Edge Length=08,09,11)
Low Feed 080202F -U 0.2 E27
U 11
TCGT 1103003F -U 0.03 3
110301F -U 0.1
110302F -U 0.2 U 08
2
TCGT 0802005MF -U < 0.05
080201MF -U < 0.1 HQ
080202MF -U < 0.2 1
0.1 0.2 0.3 0.4
TCGT 1103005MF -U < 0.05 f (mm / rev)
110301MF -U < 0.1
Sharp Edge 110302MF -U < 0.2
110304MF -U < 0.4
Insert whose corner R(r) dimension expressed with less than sign (e.g.<0.05, <0.1, <0.2 etc.) indicate models with minus tolerance for corner R (r).
TN30 PV30 PV60 PV90 PV7020 Reference Page B65
CA4010 CA4115 CA4120 PR915 PR905
Inserts are sold in 10 piece boxes.
B63
: Std. Item R : Std. Item (R-hand Only) L : Std. Item (L-hand Only) : Check Availability
для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru