Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
[Cermet / Coated Carbide / Carbide]
55°Rhombic / Positive with Hole Description A (mm)
T d
DC_0702_ 6.35 2.38 2.8 7
DC_11T3_ 9.525 3.97 4.4 7
P Free-Cutting Steel B
Classification of usage
Ar M Positive
d Carbon steel / Alloy steel Insert
K : Interruption / 1st Choice
$
N Stainless Steel %
: Interruption / 2nd Choice 3
55 T S 4
Description Gray Cast Iron
Insert H : Light Interruption / 1st Choice
Handed insert Nodular Cast Iron
shows L-Hand : Light Interruption / 2nd Choice
Sharp Edge Non-ferrous Metals
: Continuous / 1st Choice
Heat-Resistant Alloys
: Continuous / 2nd Choice
Titanium Alloy
(In case hardness is under 45HRC)
Hard materials
Dim. TN6010CermetMEGACOATCVD CoatedPVD Coated MEGACOAT
(mm) TN6020Cermet Carbide Carbide
Applicable
r TN60 Chipbreaker Range
PV7005
PV7010 (ap indicates radius)
PV7025
CA5505
CA5515
CA5525
CA5535
CA6515
CA6525
CA4505
CA4515
PR930
PR1005
PR1025
PR1125
PR1225
PR1305
PR1310
PR1325
KW10 Carbide
SW05
Ref. Page for
Toolholder
Finishing-Medium DCGT 070201MF-GQ < 0.1 (mm) (Steel) 5
070202MF-GQ < 0.2 4 GK 7
070204MF-GQ < 0.4 8
3
DCGT 11T301MF-GQ < 0.1 ap GQ Insert (Turning)
11T302MF-GQ < 0.2
Finishing-Medium 11T304MF-GQ < 0.4 2
DCGT 070201MFP-GQ < 0.1 1
070202MFP-GQ < 0.2 CK
070204MFP-GQ < 0.4
DCGT 11T301MFP-GQ < 0.1 0.1 0.2 0.3
11T302MFP-GQ < 0.2
11T304MFP-GQ < 0.4 f (mm/rev)
Sharp Edge / Polished
Finishing-Medium DCMT 070202GK 0.2 (mm) (Steel / Edge Length=07)
070204GK 0.4 3 Standard
070208GK 0.8
ap 2
DCMT 11T302GK 0.2
11T304GK 0.4 Refer to the table below 1
11T308GK 0.8 HQ
Finishing-Medium DCMT 070202HQ 0.2 XP
070204HQ 0.4
070208HQ 0.8 0.1 0.2 0.3 0.4
f (mm/rev)
DCMT 11T302HQ 0.2 (mm) (Steel / Edge Length=07,11)
11T304HQ 0.4 4
11T308HQ 0.8
3 Standard 11
DCGT 070201 0.1 ap
070202 0.2
070204 0.4 2
Conventional
DCGT 11T301 0.1
11T302 0.2 1 ( 07 )
11T304 0.4
Medium DCMT 11T308 0.8 0.1 0.2 0.3 0.4
DCGT 0702005M < 0.05 f (mm/rev)
070201M < 0.1
070202M < 0.2 (mm)
070204M < 0.4 (Steel / Edge Length=11)
DCGT 11T3005M < 0.05 4
11T301M < 0.1
11T302M < 0.2 3 Standard
11T304M < 0.4
ap HQ
2
Medium DCGT 0702005MF < 0.05 1 XQ
070201MF < 0.1 XP
070202MF < 0.2
070204MF < 0.4 0.1 0.2 0.3 0.4
DCGT 11T3005MF < 0.05 f (mm/rev)
11T301MF < 0.1
Sharp Edge 11T302MF < 0.2
11T304MF < 0.4
Insert whose corner R (r) dimension expressed with less than sign (e.g.<0.05, <0.1, <0.2 etc.) indicate models with minus tolerance for corner R (r).
Insert Description Ref. Page for Toolholder
DC..07type E22~25,E34,F35~39
DC..11type E22~25,E34,F35~39,F66
TN30 PV30 PV60 PV90 PV7020 Reference Page B58
CA4010 CA4115 CA4120 PR915 PR905
Inserts are sold in 10 piece boxes.
B53
: Std. Item R : Std. Item (R-hand Only) L : Std. Item (L-hand Only)
для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru