Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
Turning Indexable Inserts
55°Rhombic / Positive with Hole Description A (mm)
T d
DC_0702_ 6.35 2.38 2.8 7
DC_11T3_ 9.525 3.97 4.4 7
B P Free-Cutting Steel
Classification of usage
Positive Ar M
Insert d Carbon steel / Alloy steel
K : Interruption / 1st Choice
$
% N Stainless Steel
3 : Interruption / 2nd Choice
4 55 T S
5 Description Gray Cast Iron
7 Insert H : Light Interruption / 1st Choice
8
Handed insert Nodular Cast Iron
shows L-Hand : Light Interruption / 2nd Choice
Sharp Edge Non-ferrous Metals
: Continuous / 1st Choice
Heat-Resistant Alloys
: Continuous / 2nd Choice
Titanium Alloy
(In case hardness is under 45HRC)
Hard materials
Dim. TN6010CermetMEGACOATCVD CoatedPVD Coated MEGACOAT
(mm) TN6020Cermet Carbide Carbide
Applicable
r TN60 Chipbreaker Range
PV7005
PV7010 (ap indicates radius)
PV7025
CA5505
CA5515
CA5525
CA5535
CA6515
CA6525
CA4505
CA4515
PR930
PR1005
PR1025
PR1125
PR1225
PR1305
PR1310
PR1325
KW10 Carbide
SW05
Ref. Page for
Toolholder
DCGT 070202CF 0.2
DCGT 11T302CF 0.2 (mm)
0.3
Minute ap DCGT 070201M-CF < 0.1 (Steel / Edge Length=07,11)
070202M-CF < 0.2 0.2 GP
DCGT 11T301M-CF < 0.1 ap
11T302M-CF < 0.2
Insert (Turning) 0.1 CF
Minute ap DCGT 070201MP-CF < 0.1 0.05 0.1 0.15 0.2
070202MP-CF < 0.2
f (mm/rev)
Sharp Edge / Polished DCGT 11T301MP-CF < 0.1
11T302MP-CF < 0.2
Finishing
DCGT 070201MF-GF < 0.1
070202MF-GF < 0.2
DCGT 11T301MF-GF < 0.1 (mm) (Steel)
11T302MF-GF < 0.2 3
Sharp Edge 11T304MF-GF < 0.4
Sharp Edge / Polished
DCGT 070201MFP-GF < 0.1 Refer to the table below 2 GQ
With Honing 070202MFP-GF < 0.2
Finishing 070204MFP-GF < 0.4 ap 1 GF
DCGT 11T301MFP-GF < 0.1 CF
11T302MFP-GF < 0.2 0.05 0.1 0.15 0.2
11T304MFP-GF < 0.4
f (mm/rev)
DCGT 070201CK 0.1
070202CK 0.2
Finishing DCGT 11T301CK 0.1
11T302CK 0.2
DCGT 070201M-CK < 0.1 (mm) (Steel)
070202M-CK < 0.2 4
DCGT 11T301M-CK < 0.1 ap 3 GK
11T302M-CK < 0.2 GQ
2
Finishing DCGT 070201MP-CK < 0.1 1
070202MP-CK < 0.2 CK
Sharp Edge / Polished DCGT 11T301MP-CK < 0.1 0.1 0.2 0.3
11T302MP-CK < 0.2
f (mm/rev)
Finishing DCMT 070202GP 0.2
070204GP 0.4
DCMT 11T304GP 0.4
11T308GP 0.8
Insert whose corner R (r) dimension expressed with less than sign (e.g.<0.05, <0.1, <0.2 etc.) indicate models with minus tolerance for corner R (r).
Insert Description Ref. Page for Toolholder
DC..07type E22~25,E34,F35~39
DC..11type E22~25,E34,F35~39,F66
TN30 PV30 PV60 PV90 PV7020 Reference Page B58
CA4010 CA4115 CA4120 PR915 PR905
Inserts are sold in 10 piece boxes.
B52
: Std. Item R : Std. Item (R-hand Only) L : Std. Item (L-hand Only)
для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru