Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
Turning Indexable Inserts
Small Double Sided Tools Description A T (mm)
TN_U0903_ 5.56 3.18 d
3.0
B 60 P Q Free-Cutting Steel Classification of usage
rT M QP Carbon steel / Alloy steel T: Interruption / 1st Choice
Negative K PQ Stainless Steel S: Interruption / 2nd Choice
C N Gray Cast Iron Q: Light Interruption / 1st Choice
D A d S Nodular Cast Iron P: Light Interruption / 2nd Choice
R H Non-ferrous Metals N: Continuous / 1st Choice
S Heat-Resistant Alloys O: Continuous / 2nd Choice
T Titanium Alloy (In case hardness is under 45HRC)
V Hard materials
W
Dim. Cermet MEGACOAT CVD PVD MEGACOAT Carbide Ref. Page for Applicable
(mm) Cermet Coated Carbide Coated Carbide Chipbreaker Range
Toolholder
Insert Description r TN6010TN6020TN60PV7005PV7010PV7025CA5505CA5515CA5525CA5535CA6515CA6525CA4505CA4515PR930PR1005PR1025PR1125PR1225PR1305PR1310PR1325KW10 (ap indicates radius)
SW05
Handed insert
shows R-Hand
Finishing TNGU 0903005MF&-F < 0.05 RR R
090301MF&-F < 0.1 RR R
Sharp Edge 090302MF&-F < 0.2 RR R (mm) (Steel)
Sharp Edge 090304MF&-F < 0.4 RR R 4
Insert (Turning) Low Feed E17 ap U
TNGU 0903005MF&-U < 0.05 RR R 3
090301MF&-U < 0.1 RR R
090302MF&-U < 0.2 RR R 2
090304MF&-U < 0.4 RR R
1
Low Feed TNGU 090301ME&-U < 0.1 RR F
090302ME&-U < 0.2 RR
090304ME&-U < 0.4 RR 0.05 0.1 0.15 0.2
f (mm/rev)
With Honing
Insert whose corner R(r) dimension expressed with less than sign (e.g.<0.05, <0.1, <0.2 etc.) indicate models with minus tolerance for corner R (r).
Double Sided Tools (Sharp Edge / Polished)
Description A T (mm) P Free-Cutting Steel Classification of usage
d Drawing M Carbon steel / Alloy steel T: Interruption / 1st Choice
CN_1204_ 12.70 4.76 K P Stainless Steel S: Interruption / 2nd Choice
5.16 B18 N Q Gray Cast Iron Q: Light Interruption / 1st Choice
Nodular Cast Iron P: Light Interruption / 2nd Choice
DN_1504_ 12.70 4.76 5.16 B23 Non-ferrous Metals N: Continuous / 1st Choice
Heat-Resistant Alloys O: Continuous / 2nd Choice
TN_1604_ 9.525 4.76 3.81 B34 Titanium Alloy (In case hardness is under 45HRC)
Hard materials
Medium and rough cutting inserts for
automatic lathe.
S
H
Dim. Cermet MEGACOAT CVD PVD MEGACOAT Carbide Ref. Page for Applicable
(mm) Cermet Coated Carbide Coated Carbide Chipbreaker Range
Toolholder
Insert Description r TN6010TN6020TN60PV7005PV7010PV7025CA5505CA5515CA5525CA5535CA6515CA6525CA4505CA4515PR930PR1005PR1025PR1125PR1225PR1305PR1310PR1325KW10 (ap indicates radius)
SW05
Medium-Roughing Medium-Roughing Medium-Roughing CNGG 120404FP-TK 0.4 N E1 8 (mm) (Stainless Steel)
120408FP-TK 0.8 N D 8 5
F 64 4
Sharp Edge / Polished N F6 8 3
N 2
DNGG 150404FP-TK 0.4 ap 1
150408FP-TK 0.8 N
N DD 1110
Sharp Edge / Polished F6 5
TNGG 160404FP-TK 0.4 E1 9 0.1 0.2 0.3 0.4 0.5
160408FP-TK 0.8 DDF 611545 f (mm/rev)
F7 0
Sharp Edge / Polished
B44 : Std. Item R : Std. Item (R-hand Only) L : Std. Item (L-hand Only) Inserts are sold in 10 piece boxes.
для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru