Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
[Cermet / Coated Carbide / Carbide]
Small Double Sided Tools (mm)
Description A T d
DN_U0803_ 7.0 3.18 3.6
P Free-Cutting Steel Classification of usage B
Carbon steel / Alloy steel : Interruption / 1st Choice
Ar M Stainless Steel : Interruption / 2nd Choice Negative
d Gray Cast Iron : Light Interruption / 1st Choice C
K Nodular Cast Iron : Light Interruption / 2nd Choice D
Non-ferrous Metals : Continuous / 1st Choice R
N Heat-Resistant Alloys : Continuous / 2nd Choice S
Titanium Alloy T
55 T S Hard materials (In case hardness is under 45HRC) V
Description W
Insert H
Handed Insert Dim. Cermet MEGACOAT CVD PVD Carbide Ref. Page for
shows R-hand (mm) Cermet
Coated Carbide Coated Carbide Toolholder Applicable
Chipbreaker Range
r TN6010TN6020TN60PV7005PV7010PV7025CA5505CA5515CA5525CA5535CA6515CA6525CA4505CA4515PR930PR1005PR1025PR1125PR1225PR1305PR1310PR1325KW10
SW05 (ap indicates radius)
Finishing-Medium Finishing-Medium Finishing-Medium DNGU 080301MF-SK < 0.1
080302MF-SK < 0.2
080304MF-SK < 0.4
Sharp Edge
DNGU 080301MFP-SK < 0.1 Insert (Turning)
080302MFP-SK < 0.2
080304MFP-SK < 0.4
Sharp Edge / Polished
DNMU 080302E-GK 0.2 (mm) (Steel)
080304E-GK 0.4 4
U
3
With Honing E16 ap 2 GK
Sharp Edge SK
Sharp Edge DNGU 0803005MF -F < 0.05
080301MF -F < 0.1 1
080302MF -F < 0.2
Finishing 080304MF -F < 0.4 F
DNGU 0803005MF -U < 0.05 0.05 0.1 0.15 0.2
080301MF -U < 0.1 f (mm/rev)
080302MF -U < 0.2
Low Feed 080304MF -U < 0.4
Low Feed DNGU 080301ME -U < 0.1
080302ME -U < 0.2
080304ME -U < 0.4
With Honing
Insert whose corner R(r) dimension expressed with less than sign (e.g.<0.05, <0.1, <0.2 etc.) indicate models with minus tolerance for corner R (r).
Chipbreaker Selection (Negative Inserts)
Cutting Range Name cross-section Advantages
Finishing-Medium SK 16° A low cutting force chipbreaker designed for chip control in steel and
13° stainless steel.
Cutting performance is similar to comparable sized positive inserts.
Medium-Roughing GK 0.06
17° Chipbreaker “dot” and pocket design provide chip control at multiple depth of cut
and feed rates.
0.06
17°
Finishing F 18° Control chip evacuation direction with low cutting force.
Low Feed 35° Good chip control at low feed rate and varied depths of cut with low cutting force.
U
: Std. Item R : Std. Item (R-hand Only) L : Std. Item (L-hand Only) B43Inserts are sold in 10 piece boxes.
для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru