Kyocera - Основной каталог 2011-2012 ENG
Slotting, Shouldering Multi-purpose ( )для заказа - kyocera@kyocera-tools.ru
4PGRM Workpiece Materials No. of Flutes: 4
1st choice
Radius I
R
NN Shank Dia.
3
-
4 %D
%
S %T
4PGRM Solid End MillShouldering Slotting
(Unit : mm)
Description Std. Outside Dia. Mill Dia. Length of cut Neck Dia. Under Neck Shank Overall length Spec of
Dc tolerance D1 Length diameter L Corners
4PGRM030-045-06-R025
4PGRM030-045-06-R050 2 Ds
4PGRM040-060-06-R025
4PGRM040-060-06-R050 3 -0.014 4.5 2.7 9 6 57 R 0.25
4PGRM050-075-06-R025 -0.028
4PGRM050-075-06-R050
4PGRM060-090-06-R025 3 -0.014 4.5 2.7 9 6 57 R 0.5
4PGRM060-090-06-R050 -0.028
4PGRM060-090-06-R075
4PGRM060-090-06-R100 4 -0.020 6 3.7 12 6 57 R 0.25
4PGRM080-120-08-R050 -0.038
4PGRM080-120-08-R100
4PGRM080-120-08-R150 4 -0.020 6 3.7 12 6 57 R 0.5
4PGRM080-120-08-R200 -0.038
4PGRM100-150-10-R050
4PGRM100-150-10-R100 5 -0.020 7.5 4.6 15 6 76 R 0.25
4PGRM100-150-10-R150 -0.038
4PGRM100-150-10-R200
4PGRM120-180-12-R050 5 -0.020 7.5 4.6 15 6 76 R 0.5
4PGRM120-180-12-R100 -0.038
4PGRM120-180-12-R150
4PGRM120-180-12-R200 6 -0.020 9 5.5 18 6 76 R 0.25
4PGRM160-240-16-R050 -0.038
4PGRM160-240-16-R150
4PGRM200-300-20-R050 6 -0.020 9 5.5 18 6 76 R 0.5 L
4PGRM200-300-20-R200 -0.038
No. of Flutes Z=4
6 -0.020 9 5.5 18 6 76 R 0.75
-0.038
6 -0.020 9 5.5 18 6 76 R 1.0
-0.038
8 -0.025 12 7.4 24 8 100 R 0.5
-0.047
8 -0.025 12 7.4 24 8 100 R 1.0
-0.047
8 -0.025 12 7.4 24 8 100 R 1.5
-0.047
8 -0.025 12 7.4 24 8 100 R 2.0
-0.047
10 -0.025 15 9.2 30 10 100 R 0.5
-0.047
10 -0.025 15 9.2 30 10 100 R 1.0
-0.047
10 -0.025 15 9.2 30 10 100 R 1.5
-0.047
10 -0.025 15 9.2 30 10 100 R 2.0
-0.047
12 -0.032 18 11 36 12 125 R 0.5
-0.059
12 -0.032 18 11 36 12 125 R 1.0
-0.059
12 -0.032 18 11 36 12 125 R 1.5
-0.059
12 -0.032 18 11 36 12 125 R 2.0
-0.059
16 -0.032 24 15 48 16 125 R 0.5
-0.059
16 -0.032 24 15 48 16 125 R 1.5
-0.059
20 -0.040 30 19 60 20 150 R 0.5
-0.073
20 -0.040 30 19 60 20 150 R 2.0
-0.073
Radius type with 4 utes. The diameter of the neck portion is thinner than the cutting diameter and it is suitable for deep slotting.
Due to the corner R on the cutting edge, it is applicable for nishing of sloped workpieces.
Recommended Cutting Conditions L39
: Check Availability
для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru L17