Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
Surface finish oriented
No. of Flutes: 4
4 flutes, Sharp corner edge 4 flutes, Tough corner edge
4FESM 4FEKM
Workpiece Materials 1st choice Workpiece Materials 1st choice
-f -f
MEGACOAT is applied MEGACOAT is applied
4 4
Super Micro-grain carbide Super Micro-grain carbide
Sharp I Land I
Shank Dia. Shank Dia.
%D
%
%TI
%D
%
%TI
-
-
4FESM Shouldering 4FEKM Shouldering L
Description (Unit : mm) Description (Unit : mm)
Outside Length Neck Shank Overall No. of Outside Length Neck Under Neck Shank Overall No. of
Dia. diameter length Flutes
Std. Dia. Mill Dia. of cut Std. Dia. Mill Dia. of cut Dia. Length diameter length Flutes
D1 Dc tolerance D1
tolerance 2 Ds L Z
Dc
Ds L Z
4FESM010-025-04 1.0 0 2.5 1.1 4 45 4 4FEKM030-100-06 3.0 0 10.0 3.15 12 6 49.8 4 Solid End Mill
4FESM015-040-04 1.5 -0.015 4.0 1.6 4 45 4 -0.015
4FESM020-060-04 2.0 6.0 2.1 4 45 4
4FESM025-080-04 2.5 0 8.0 2.6 4 45 4 4FEKM035-100-06 3.5 0 10.0 3.68 12 6 49.8 4
4FESM030-100-06 3.0 -0.015 10.0 3.2 6 50 4 -0.015
4FESM035-100-06 3.5 10.0 3.7 6 50 4
4FESM040-110-06 4.0 0 11.0 4.2 6 50 4 4FEKM040-110-06 4.0 0 11.0 4.2 13.2 6 49.8 4
4FESM045-110-06 4.5 -0.015 11.0 4.7 6 50 4 -0.015
4FESM050-130-06 5.0 13.0 5.2 6 50 4
4FESM055-130-06 5.5 0 13.0 5.7 6 50 4 4FEKM045-110-06 4.5 0 11.0 4.7 13.2 6 49.8 4
4FESM060-130-06 6.0 -0.015 13.0 6 50 4 -0.015
4FESM080-190-08 8.0 19.0 - 8 60 4
4FESM100-220-10 10.0 0 22.0 - 10 70 4 4FEKM050-130-06 5.0 0 13.0 5.2 15.6 6 49.8 4
4FESM120-260-12 12.0 -0.015 26.0 - 12 75 4 -0.015
4FESM140-260-16 14.0 26.0 - 16 75 4
4FESM150-300-16 15.0 0 30.0 14.2 16 90 4 4FEKM055-130-06 5.5 0 13.0 5.7 15.6 6 49.8 4
4FESM160-320-16 16.0 -0.015 32.0 15.2 16 90 4 -0.015
-
0 4FEKM060-130-06 6.0 0 13.0 - - 6 49.8 4
-0.015 -0.020
0 4FEKM080-190-08 8.0 -0.005 19.0 - - 8 59.8 4
-0.015 -0.025
0 4FEKM100-220-10 10.0 -0.005 22.0 - - 10 69.8 4
-0.015 -0.025
0 4FEKM120-260-12 12.0 -0.010 26.0 - - 12 74.8 4
-0.015 -0.030
0 4FEKM140-260-16 14.0 -0.010 26.0 14.2 36.4 16 74.8 4
-0.020 -0.030
-0.005 4FEKM150-300-16 15.0 -0.010 30.0 15.2 42 16 89.8 4
-0.025 -0.030
-0.005 4FEKM160-320-16 16.0 -0.010 32.0 - - 16 89.8 4
-0.025 -0.030
-0.010
-0.030
-0.010
-0.030
-0.010
-0.030
-0.010
-0.030
Recommended Cutting Conditions L35
: Check Availability
для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru L13