Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
Surface nish oriented, 2 utes, Tough corner edge
2FEKS, 2FEKM Workpiece Materials No. of Flutes: 2
1st choice
-f
Land I
Shank Dia.
Solid End Mill MEGACOAT is applied
%D
%2-
%TISuper Micro-grain carbide
2FEKS Short Shouldering Slotting 2FEKM Medium Shouldering Slotting
(Unit : mm) (Unit : mm)
Outside Mill Dia. Length Neck Under Neck Shank Overall No. of Outside Length Neck Under Neck Shank Overall No. of
tolerance Dia. Length diameter length Flutes Mill Dia. of cut Dia. Length diameter length Flutes
Description Std. Dia. of cut Description Std. Dia. tolerance
Dc D1 2 Ds L Z Dc D1 2 Ds L Z
2FEKS030-045-06 3.0 0 4.5 3.15 6.5 6 49.8 2 2FEKM030-100-06 3.0 0 10.0 3.15 12.0 6 49.8 2
2FEKS035-052-06 -0.015 6 49.8 2 2FEKM035-100-06 -0.015
2FEKS040-060-06 6 49.8 2 2FEKM040-110-06
0 2FEKM045-110-06 3.5 0 10.0 3.68 12.0 6 49.8 2
-0.015 -0.015
3.5 5.2 3.68 7.2
0
4.0 -0.015 11.0 4.2 13.2 6 49.8 2
4.0 0 6.0 4.2 8.2 4.5 0 11.0 4.7 13.2 6 49.8 2
-0.015 -0.015
2FEKS045-067-06 4.5 0 6.7 4.7 8.9 6 49.8 2 2FEKM050-130-06 5.0 0 13.0 5.2 15.6 6 49.8 2
2FEKS050-075-06 -0.015 2FEKM055-130-06 -0.015
2FEKS055-082-06 2FEKM060-130-06
5.0 0 7.5 5.2 10.1 6 49.8 2 2FEKM065-160-08 5.5 0 13.0 5.7 15.6 6 49.8 2
-0.015 -0.015
6.0 0 13.0 - - 6 49.8 2
-0.020
0
5.5 -0.015 8.2 5.7 10.8 6 49.8 2 6.5 0 16.0 6.7 22.4 8 59.8 2
-0.020
L 2FEKS060-090-06 6.0 0 9.0 - - 6 49.8 2 2FEKM070-160-08 7.0 0 16.0 7.2 22.4 8 59.8 2
-0.020 2FEKM075-190-08 -0.020
2FEKS080-120-08 2FEKM080-190-08
8.0 -0.005 12.0 - - 8 59.8 2 7.5 0 19.0 7.7 26.6 8 59.8 2
-0.025 -0.020
8.0 -0.005 19.0 - - 8 59.8 2
-0.025
-0.005
2FEKS100-150-10 10.0 -0.025 15.0 - - 10 69.8 2 2FEKM085-190-10 8.5 -0.005 19.0 8.7 26.6 10 69.8 2
-0.025
2FEKS120-180-12 12.0 -0.010 18.0 - - 12 74.8 2 2FEKM090-190-10 9.0 -0.005 19.0 9.2 26.6 10 69.8 2
2FEKS140-210-16 -0.030 2 2FEKM095-190-10 -0.025 2
2FEKS150-230-16 2 2FEKM100-220-10 2
14.0 -0.010 21.0 14.2 31.4 16 74.8 2FEKM110-220-12 9.5 -0.005 19.0 9.7 26.6 10 69.8 2
-0.030 -0.025
10.0 -0.005 22.0 - - 10 69.8
-0.025
-0.010
15.0 -0.030 23.0 15.2 35 16 89.8 11.0 -0.005 22.0 11.2 30.8 12 74.8
-0.025
2FEKS160-240-16 16.0 -0.010 24.0 - - 16 89.8 2 2FEKM120-260-12 12.0 -0.010 26.0 - - 12 74.8 2
-0.030 -0.030
2FEKM130-260-16 13.0 -0.010 26.0 13.2 36.4 16 74.8 2
-0.030
2FEKM140-260-16 14.0 -0.010 26.0 14.2 36.4 16 74.8 2
-0.030
2FEKM150-300-16 15.0 -0.010 30.0 15.2 42.0 16 89.8 2
-0.030
2FEKM160-320-16 16.0 -0.010 32.0 - - 16 89.8 2
-0.030
MEGACOAT and sharp cutting edge enable high precision nishing owing to excellent wear and heat-resistance.
L12 Recommended Cutting Conditions L34
: Check Availability
для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru