Kyocera - Основной каталог 2011-2012 ENG
2 Edges Tip-Bar for Micro Internal Threading HPTдля заказа - kyocera@kyocera-tools.ru [Solid]
HPT (Micro Internal Threading)
A H
L1
0°
dd
L2
L3
S
F
S
D
r
dd
Details of Edge
Right-hand shown
Dimensions
Min. Insert Grade Applicable Thread
Bore Dimension (mm) PVD Coated Carbide Metric Unied
Dia. Carbide
Description
A D H L1 L2 L3 F S d r PR930 KW10 Nominal Pitch (mm) Nominal Pitch
Thread Thread (TPI)
HPTR 04504-60-005 4.5 4 3.7 60 16 3.9 1.3 0.6 M6 and P0.75 1/4-20UNC 28~20
06005-60-005 6 over ~P1.25 1/4-28UNF and over
07507-60-005 7.5 8
M8 and P0.75 5/16-18UNC
5 4.6 70 21 4.9 1.6 0.8 0.05 60° over ~P1.50 5/16-24UNF and over 24~18
7 6.4 80 26 10 6.9 2 1 M10 and P0.75 3/8-16UNC 24~16
over ~P1.50 3/8-24UNF and over
Whitworth Parallel Pipe
Tapered Pipe
HPTR 06005-55-010 6 5 4.6 70 21 8 4.9 1.6 0.8 W10 TPI 20 24~20 G1/16 and over 28
W10 TPI 24 and over 20~18 R1/16 and over
J 0.1 55°
08007-55-010 8 7 6.4 80 26 10 6.9 2.0 1.0 W11 TPI 18 G1/8 and over 28~19
W11 TPI 20 and over R1/8 and over
Description Table for Tip-Bars and Applicable Sleeves Recommended Cutting Conditions
Description Applicable Sleeve Workpiece Material Recommended Insert Grade
J26 (Cutting Speed: m/min)
1) The standard cutting
Threading PVD Coated Carbide Carbide speed is Vc=30~50m/
min. The table feed
HPTR 04504-60-005 PSH 04 - PR930 KW10 may not follow the
HPTR 06005-60-005 PSH 05 - expected conditions
07507-60-005 07 - Carbon Steel / Alloy Steel 30~100 when machining small
06005-55-010 05 - diameter workpieces at
08007-55-010 07 - Stainless Steel 30~80 high speeds.
2) Coolant is recommended.
Non-ferrous Metals ~300
: 1st Recommendation : 2nd Recommendation
Depth of Cut & Number of Passes (Metric / M)
Pitch Total ap No. of 1 Pass 2 Pass 3 Pass 4 Pass 5 Pass 6 Pass 7 Pass 8 Pass 9 Pass 10 Pass 11 Pass 12 Pass 13 Pass 14 Pass 15 Pass 16 Pass 17 Pass
(mm) (mm) Passes
0.75 0.44 10 0.06 0.06 0.05 0.05 0.05 0.04 0.04 0.03 0.03 0.03
1.00 0.60 12 0.07 0.07 0.06 0.06 0.06 0.05 0.05 0.04 0.04 0.04 0.03 0.03
1.25 0.76 14 0.07 0.07 0.07 0.07 0.06 0.06 0.06 0.05 0.05 0.05 0.04 0.04 0.04 0.03
1.50 0.92 17 0.07 0.07 0.07 0.07 0.06 0.06 0.06 0.06 0.05 0.05 0.05 0.05 0.04 0.04 0.04 0.04 0.03
Depth of Cut & Number of Passes (Whitworth / W)
TPI Total ap No. of 1 Pass 2 Pass 3 Pass 4 Pass 5 Pass 6 Pass 7 Pass 8 Pass 9 Pass 10 Pass 11 Pass 12 Pass 13 Pass 14 Pass 15 Pass 16 Pas 17 Pass
(mm) Passes
24 0.65 13 0.07 0.07 0.06 0.06 0.06 0.05 0.05 0.05 0.04 0.04 0.04 0.03 0.03
20 0.81 15 0.07 0.07 0.07 0.07 0.06 0.06 0.06 0.06 0.05 0.05 0.05 0.04 0.04 0.03 0.03
18 0.91 17 0.07 0.07 0.07 0.07 0.07 0.06 0.06 0.06 0.06 0.05 0.05 0.05 0.04 0.04 0.03 0.03 0.03
Depth of Cut & Number of Passes (Unied / UN. UNC. UNF. UNEF)
TPI Total ap No. of 1 Pass 2 Pass 3 Pass 4 Pass 5 Pass 6 Pass 7 Pass 8 Pass 9 Pass 10 Pass11 Pass12 Pass13 Pass14 Pass15 Pass16 Pass 17 Pass 18 Pass
(mm) Passes
28 0.54 12 0.07 0.06 0.05 0.05 0.05 0.05 0.04 0.04 0.04 0.03 0.03 0.03
24 0.64 12 0.07 0.06 0.06 0.06 0.06 0.06 0.05 0.05 0.05 0.05 0.04 0.03
20 0.77 14 0.07 0.07 0.07 0.06 0.06 0.06 0.06 0.06 0.05 0.05 0.05 0.04 0.04 0.03
18 0.87 17 0.07 0.07 0.07 0.06 0.06 0.06 0.06 0.06 0.05 0.05 0.05 0.04 0.04 0.04 0.03 0.03 0.03
16 0.98 18 0.07 0.07 0.07 0.07 0.06 0.06 0.06 0.06 0.06 0.05 0.05 0.05 0.05 0.05 0.04 0.04 0.04 0.03
Tip-Bars are sold : Std. Item : Check Availability
in 1 piece boxes.
J24 для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru