Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
Recommended Cutting Conditions
TKF12/16 Recommended Cutting Conditions
Recommended Grade Vc m/min
Workpiece Material Width W mm Width W mm Remarks
Carbon Steel (SxxC) MEGACOAT PVD Coated Carbide Carbide 0.5 0.7 1.0 1.5 2.0 1.5 2.0
Alloy Steel (SCM)
Stainless Steel (SUS304) PR1225 PR1025 KW10 Feed Rate mm/rev Feed Rate mm/rev
70 ~ 150 60 ~ 130 - 0.01 ~ 0.02 0.01 ~ 0.03 0.01 ~ 0.04 0.01 ~ 0.04 0.01 ~ 0.04 0.02 ~ 0.07 0.02 ~ 0.07
0.01 0.05 0.01 0.07 0.01 0.07 0.02 0.1 0.02 0.1
70 ~ 150 60 ~ 130 - 0.01 ~ 0.02 0.01 ~ 0.03 0.01 ~ 0.04 0.01 ~ 0.04 0.01 ~ 0.04 0.02 ~ 0.07 0.02 ~ 0.07
0.01 0.05 0.01 0.07 0.01 0.07 0.02 0.1 0.02 0.1
60 ~ 120 50 ~ 100 - 0.005 ~ 0.015 0.01 ~ 0.02 0.01 ~ 0.02 0.01 ~ 0.02 0.01 ~ 0.02 0.01 ~ 0.04 0.01 ~ 0.04 Coolant
0.01 0.03 0.01 0.03 0.01 0.03 0.02 0.04 0.02 0.04
Cast Iron ( FC/FCD) - - 50 ~ 100 0.01 ~ 0.03 0.01 ~ 0.04 0.01 ~ 0.05 0.01 ~ 0.05 0.01 ~ 0.05 0.02 ~ 0.08 0.02 ~ 0.08
Aluminium - - 200 ~ 450 0.01 ~ 0.03 0.01 ~ 0.04 0.01 ~ 0.05 0.01 ~ 0.05 0.01 ~ 0.05 0.02 ~ 0.08 0.02 ~ 0.08
Workpiece Material PCD Remarks ( ): Tough edge type (TKF..T..)
KPD001 Coolant
Grooving Traversing 1st Recommendation
2nd Recommendation
200 500
Aluminium Vc m/min H
Brass Feed Rate mm/rev 0.01 0.03 0.02 0.12
Vc m/min 100 350
Feed Rate mm/rev
0.01 0.05 0.02 0.15
Recommended Cutting Conditions (In case of using GMM-MT, GMM-TK, GMM-NB insert)
Recommended Insert Grade (Vc: m/min) Dimension (mm) Remarks
Workpiece Material Cermet CVD Coated Carbide PVD Coated Carbide Carbide 1.5 2.0 / 2.5 3.0 4.0 Cut-off
- CR9025 PR915 PR930 KW10 f (mm/rev)
Carbon Steel - 80~180 60~150 60~130 0.01~0.04 0.02~0.15 0.03~0.20 0.08~0.30
Alloy Steel - 70~150 60~150 60~130 0.01~0.04 0.02~0.15 0.03~0.20 0.08~0.30 Coolant
Stainless Steel - 60~140 50~140 50~120 0.01~0.03 0.02~0.10 0.03~0.15 0.08~0.25
Cast Iron - - - - 50~100 0.01~0.05 0.05~0.12 0.10~0.25 0.10~0.30
Non-ferrous Metals - - - - 200~450 0.01~0.05 0.05~0.10 0.05~0.20 0.05~0.25
• When machining Steel and Stainless Steel by 4mm width Insert of PR930, decrease the Feed Rate by 20%. : 1st Recommendation : 2nd Recommendation
Recommended Cutting Conditions (TKN, TK type Insert)
Recommended Insert Grade (Vc: m/min) Dimension (mm) Remarks
Workpiece Material Cermet CVD Coated Carbide PVD Coated Carbide Carbide 1.6 2.2 / 2.4 3.1 4.1 4.8~9.6
TN90 CR9025 PR660 PR930 KW10 f (mm/rev)
Carbon Steel 120~200 80~180 60~130 60~130 0.02~0.08 0.04~0.18 0.05~0.25 0.08~0.30 0.15~0.40
Alloy Steel 100~160 70~150 60~130 60~130 0.02~0.08 0.04~0.18 0.05~0.25 0.08~0.30 0.15~0.40
Stainless Steel 80~150 60~40 50~120 60~140 0.02~0.06 0.04~0.12 0.05~0.18 0.08~0.25 0.10~0.30 Coolant
Cast Iron - - - - 50~100 0.02~0.08 0.05~0.12 0.10~0.25 0.10~0.30 0.15~0.35
Non-ferrous Metals - - - - 100~450 0.02~0.10 0.05~0.10 0.05~0.20 0.05~0.25 0.10~0.25
: 1st Recommendation : 2nd Recommendation
Recommended Cutting Conditions (In case of using GMM-TMR type Insert)
Workpiece Material Vc (m/min) f (mm/rev) Remarks
Carbon Steel 60~200 0.08~0.18 Coolant
Alloy Steel 60~150
Stainless Steel 50~140
для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru H25
