Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
Cut-Off Toolholders (Integral Shank)
KTKH-S
For General Cut-Off (Self Clamp)
H1 B H2 H3 W W
H1 B L2 DDhh Fig.1
L1 WW
L2
H3
L1
Right-hand shown Fig.2
H Toolholder Dimensions
Std. Cut-Off Dimension (mm) Width Spare Parts Ref.Page for
Dia. (mm) Recommended
Releasing Wrench
Drawing Cutting
Description L2 W Conditions
R L Dmax H1=h H2 H3 B L1
Cut-off KTKH 1010F-2S 30 10 5 4 10 80 18.6
KTKH 1212H-2S 33 12 4
1612H-2S 33 16 - 5 12 100 19.8
1616H-2S 33 16 -
2012K-2S 38 20 - 3 12 100 19.8 2.2 Fig.1
2020K-2S 38 20 - 3 16 100 19.8 2.4
36 16 4
1612H-3S 36 16 4 4 12 125 22.8
1616H-3S 41 20 -
2012K-3S 52 20 - 4 20 125 22.8
2020K-3S 53 25 -
2525M-3S 44 20 - 4 12 100 21.7
62 20 -
2012K-4S 68 25 - 4 16 100 21.7 Fig.1 LTK-5 H25
2020K-4S 79 25 - LTK-5 H25
2525M-4S 35 20 - 5 12 125 25.3 3.1
2525M-5S 45 25 -
2020K-3T17S 45 20 - 5 20 125 31.0 Fig.2
2525M-3T22S 45 25 - 5 25 150 31.5
2020K-4T22S
2525M-4T22S H21 5 12 125 26.3 Fig.1
5 20 125 35.0 4.1 Fig.2
5 25 150 38.0
5 25 150 43.5 4.8, 5.1 Fig.2
5 20 125 21.8 3.1 Fig.1
5 25 150 26.8 4.1
5 20 125 26.8
5 25 150 26.8
Applicable Inserts Application Example of CERACUT Cut-Off
Ref. Page 1. Cut-Off after Chamfering
Grooving Chamfering Cut-Off
Insert
Toolholder TKN2 Low Feed Lead Angle Low Feed / Lead-Angled 2. Wide Grooving
TKN2.4
KTKH ...-2... TKN2-P TK 2 TK 2-P ~ Groove Widening
KTKH ...-3... TKN3 TKN3-P TK 2.4
KTKH ...-4... TK 3-P
KTKH ...-5... TKN4 - TK 3
-
TKN4.8 Longitudinal Finishing
TKN5
TK 4 - (Value of “ap” shall be under the value of
Corner-R) ap
TK 5 -
H24 (In order to prevent both corners' unequal wear)
: Std. Item : Check Availability
для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru