Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
KGD-S Straight : 0°, Separate Type
F1 T H1 B
W L2
h H2 H3
A L1
R-hand Shown
Toolholder Dimensions Toolholder+Blade
Shank Angle Std. Dimension mm Width W
Width (mm) Blade mm
Assembly Number Description Description
Available Grooving (Standard G28 T MIN MAX
Depth (mm) G28 H1=h H2
Stock Number) RL H3 B L1 L2 L3 F1 A
KGD 2020X-2T17S KGD 2020-C 20 12 20 122 23.4 H
2 17 39.9 1.7 17 2.0
KGD 2525-C KGD -2T17-C 25 7 3.0
2525X-2T17S 25 147 28.4 4.0
KGD 2020X-3T10S KGD 2020-C 20 12 20 115 23.0 5.0
10 2525X-3T10S KGD 2525-C KGD -3T10-C 25 7 25 140 32.9 28.0 10 6.0
H13
3232X-3T10S KGD 3232-C 32 - 32 160 33.0 3.0 Cut-off
3 KGD 2020-C 20 12 20 125 2.4
KGD 2020X-3T20S 23.0
20 2525X-3T20S KGD 2525-C KGD -3T20-C 25 7 25 150 42.9 28.0 20
3232X-3T20S KGD 3232-C 32 - 32 170 33.0
KGD 2020X-4T10S KGD 2020-C 20 12 20 115 22.5
10 2525X-4T10S KGD 2525-C KGD -4T10-C 25 7 25 140 32.9 27.5 10
3232X-4T10S KGD 3232-C 32 - 32 160 32.5
0° KGD 2020X-4T20S KGD 2020-C 20 12 11.6 20 125 - 22.5
4 20 2525X-4T20S KGD 2525-C KGD -4T20-C 25 7 25 150 42.9 27.5 3.4 20 4.0
3232X-4T20S KGD 3232-C 32 - 32 170 32.5
KGD 2020X-4T25S KGD 2020-C 20 12 20 130 22.5
25 2525X-4T25S KGD 2525-C KGD -4T25-C 25 7 25 155 47.9 27.5 25
3232X-4T25S KGD 3232-C 32 - 32 175 32.5
KGD 2020X-5T10S KGD 2020-C 20 12 20 115 22.0
10 2525X-5T10S KGD 2525-C KGD -5T10-C 25 7 25 140 32.9 27.0 10
3232X-5T10S KGD 3232-C 32 - 32 160 32.0 5.0
5 KGD 2020-C 20 12 20 130 4.4
KGD 2020X-5T25S 22.0
25 2525X-5T25S KGD 2525-C KGD -5T25-C 25 7 25 155 47.9 27.0 25
3232X-5T25S KGD 3232 -C 32 - 32 175 32.0
Note) 1. In case of normal mounting position, the toolholder body may interfere with the tool presetter. Recommended Cutting Conditions
2. Toolholder description and blade description are printed on the toolholder body. (Unit description is not indicated.)
KGD-S : R-hand Blade for R-hand Toolholder, L-hand Blade for L-hand Toolholder.
Combination of the optional toolholder (KGD..-C) and blade (KGD..T..-C) (both separately sold) can make up the corresponding assembly part.
Make sure of the “hand of toolholder” and “hand of blade”.
3. Dimension T: Maximum depth to which processing can be made. (If the dimension T is 20 mm or more, the maximum depth of groove made by
the 2-edge insert will be 18 mm.)
4. Recommended tightening torque of clamp bolt for insert: 6.5N•m (Groove width 2 - 6 mm)
Std. Item
для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru H15