Kyocera - Основной каталог 2011-2012 ENG

                                                                           для заказа - kyocera@kyocera-tools.ru

     C5h5i°pDbi raemaoknerd /SNeelegcattiiovne /(wPiot hsitHivoel eInserts)

                       Steel

     1 Molded Chipbreaker

B Cutting                        Design  Advantages                                                                   Cutting                               Design                Advantages
                           Name                                                                                                Name
                 Range                                                                                                                                                  13        Good cutting
                                                                                                                      Range                                               20      performance.
                                                                                                                                                                                  Applicable
Insert (Turning)                         Available                                                                    Finishing                                               20  without
           Minute ap                                                                                                                                                              hand for two
                                         20 for minute                                                                                                                            direction
                                                                                                                                                                                  cutting on
                       CF                ap (0.02                                                                                       CK                                        automatic
                                                                                                                                                                                  lathe.
                                         to 0.2mm)
                                                                                                                                                                                  Good chip
                                         nishing.                                                                                                                                control at
                                                                                                                                                                                  finishing.
                                         Dot located                                                                                                                              Applicable to
                                                                                                                                                                                  sticky material
                                         close to ridge                                                                                                                           like low
                                                                                                                                                                                  carbon steel,
                                         line of cutting                                                                                                                          pipe material.

     Finishing                           edge on                                                                      Finishing

                       GF                 corner.                                                                                   GP

                                         Chips

                                         fragmented in

                                         small pieces

                                         in cutting of

                                         small ap.

                                         Enables

     Finishing-Medium                    cutting over

                                         a wide range

                                         of conditions                                                                Finishing                                                           Consistent
                                                                                                                                                            14 chip breaking
                       GQ                 by using the                                                                                DP
                                                                                                                                                                                          performance
                                         optimum                                                                                                                                          for finishing.

                                         chipbreaker

                                         width according

                                         to the cutting

                                         depth.

                                         Wide chip

                                         control                                                                      Finishing-Medium                            0.2             15
                                                                                                                                                            5                           General
                                         range and                                                                                                                                      purpose
                                                                                                                                                                  0.2                   chipbreaker
     Finishing                           sharp cutting                                                                                                      5
                                                                                                                                                                                  15 for medium
                       XP                20 performance.                                                                                HQ                                              cutting.

                                         Suitable

                                         for low

                                         carbon steel

                                         and sticky

                                         material.

                                         Wide chip

     Finishing-Medium                    0.05 control

                                                                range and                                             Medium                                    0.15                     Chipbreaker
                                 20 sharp cutting                                                                                                           5
                                                                                                                                                                                         for short chips
                       XQ                performance.                                                                                   G                                         10 at medium

                                        Suitable                                                                                                                                        cutting.

                                 20 for low

                                         carbon steel

                                         and sticky

                                         material.

     Finishing-Medium                                                             0.1                                 Medium                                  0.2                 Strong edge
                                                                                                                             Standard (Without Indication)  6                     chipbreaker
                                                                                                       Good chip                                                                  for medium
                                                                       17 evacuation at                                                                                           cutting range.

                                                                                                       wide range by
                       GK 0.1 breaker dot

                                                                                                       and wide chip
                                                                       17 pocket.

B10

                                         для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru