Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
[Cermet / Coated Carbide / Carbide]
80°Trigon / Positive with Hole Description A T d (mm)
WB_0601_ 3.97 1.59 2.3
WB_0802_ 4.76 2.38 2.3 5 B
WC_0201_ 3.97 1.59 2.3 5
7 Positive
Insert
80° P Free-Cutting Steel Classification of usage
Carbon steel / Alloy steel : Interruption / 1st Choice C
r M Stainless Steel : Interruption / 2nd Choice D
Gray Cast Iron : Light Interruption / 1st Choice R
Insert K Nodular Cast Iron : Light Interruption / 2nd Choice S
Non-ferrous Metals : Continuous / 1st Choice T
Handed insert A N Heat-Resistant Alloys : Continuous / 2nd Choice V
shows L-Hand d Titanium Alloy W
T S Hard materials (In case hardness is under 45HRC)
TN6010Description
TN6020H
TN60Dim.CermetMEGACOATCVD CoatedPVD CoatedMEGACOAT
PV7005(mm)CermetCarbideCarbide
PV7010 Applicable
PV7025r Chipbreaker Range
CA5505
CA5515 (ap indicates radius)
CA5525
CA5535
CA6515
CA6525
CA4505
CA4515
PR930
PR1005
PR1025
PR1125
PR1225
PR1305
PR1310
PR1325
KW10 Carbide
SW05
Ref. Page for
Toolholder
Minute ap WBGT 060101M -CF < 0.1
060102M -CF < 0.2
Sharp Edge Insert (Turning)
(mm) (Steel / Edge Length=06)
0.3
Minute ap WBGT 060101MP -CF < 0.1
060102MP -CF < 0.2 0.2
ap
Sharp Edge / Polished 0.1 CF
Finishing WBMT 060102 -DP 0.2 L L LL LL 0.05 0.1 0.15 0.2
060104 -DP 0.4 L L LL LL f (mm/rev)
WBMT 080202 -DP 0.2 L L LL F57
080204 -DP 0.4 L L LL F59
L
WBGT 0601003 -F 0.03 L L
060101 -F 0.1 L (mm)
060102 -F 0.2 L L (Steel / Edge Length=06,08)
060104 -F 0.4 L L
L 4
WBGT 0802003 -F 0.03 3
080201 -F 0.1
080202 -F 0.2 L L
080204 -F 0.4 L
Finishing 2
ap F DP
WBGT 0601005M -F < 0.05
060101M -F < 0.1 1
060102M -F < 0.2
060104M -F < 0.4 0.1 0.2 0.3 0.4
f (mm/rev)
WBGT 0802005M -F < 0.05
080201M -F < 0.1
080202M -F < 0.2
080204M -F < 0.4
WCGT 020101 -F 0.1 L
020102 -F 0.2
0.4 L
020104 -F L
Cast Iron WBGW 060102 0.2 L L
060104 0.4 L
F57
0.2 L F59
0.4 L L
WBGW 080202
Without Chipbreaker 080204
Insert whose corner R(r) dimension expressed with less than sign (e.g.<0.05, <0.1, <0.2 etc.) indicate models with minus tolerance for corner R (r).
Inserts are sold in 10 piece boxes. B77
: Std. Item R : Std. Item (R-hand Only) L : Std. Item (L-hand Only) : Check Availability
для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru