Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
Turning Indexable Inserts
35°Rhombic / Positive with Hole Description A T d (mm)
VP_0802_ 4.76 2.38 2.3
VP_1103_ 6.35 3.18 2.8 11
11
B r PA d Free-Cutting Steel Classification of usage
Carbon steel / Alloy steel : Interruption / 1st Choice
Positive M Stainless Steel : Interruption / 2nd Choice
Insert Gray Cast Iron : Light Interruption / 1st Choice
K Nodular Cast Iron : Light Interruption / 2nd Choice
C Non-ferrous Metals : Continuous / 1st Choice
D 35° N Heat-Resistant Alloys : Continuous / 2nd Choice
R TS Titanium Alloy
S Hard materials (In case hardness is under 45HRC)
T H
V
W Dim. Cermet MEGACOAT CVD Coated PVD Coated MEGACOAT Carbide Ref. Page for Toolholder
(mm) Cermet Carbide Carbide
Applicable
Insert Description TN6010 TN6020 TN60 PV7005 PV7010 PV7025 CA5505 CA5515 CA5525 CA5535 CA6515 CA6525 CA4505 CA4515 PR930 PR1005 PR1025 PR1125 PR1225 PR1305 PR1310 PR1325 KW10 Chipbreaker Range
SW05
Handed insert r (ap indicates radius)
shows L-Hand
Super Fine E30
E31
Insert (Turning) VPET 080201 -FSF 0.1 F51 ap (mm) (Steel / Edge Length=08)
Finishing 080202 -FSF 0.2 F55 3
2
VPET 1103003 -FSF 0.03 E30
110301 -FSF 0.1 E31
110302 -FSF 0.2
VPET 080201M -FSF < 0.1 E30 USF
080202M -FSF < 0.2 E31 1
F51
VPET 1103005M -FSF < 0.05 F55 FSF
110301M -FSF < 0.1
110302M -FSF < 0.2 E30 0.1 0.2 0.3 0.4
E31 f (mm/rev)
VPET 080201F -USF 0.1
Sharp Edge / Precision 080202F -USF 0.2 E30
Super Fine E31
F51
F55
Low Feed VPET 1103003F -USF 0.03 E30 ap(mm) (Steel / Edge Length=11)
110301F -USF 0.1 E31 3
110302F -USF 0.2 USF
E30 2 FSF
VPET 080201MF -USF < 0.1 E31
080202MF -USF < 0.2 F51 1
F55
VPET 1103005MF -USF < 0.05 E30 0.1 0.2 0.3 0.4
110301MF -USF < 0.1 E31 f (mm/rev)
110302MF -USF < 0.2
Sharp Edge / Precision
Insert whose corner R(r) dimension expressed with less than sign (e.g.<0.05, <0.1, <0.2 etc.) indicate models with minus tolerance for corner R (r).
35°Rhombic / Positive with Hole
(mm)
r Description A T d
VP_1103_ 6.35 3.18 2.8 11°
35° A
dT
Insert TN30 Cermet
PV30
Handed insert PV60
shows L-Hand PV90
PV7020
CA4010
CA4115
CA4120
PR915
PR905
Ref. Page for
Toolholder
Dim. PVD CVD PVD
(mm) Coated Coated Coated
Cermet Carbide Carbide
Description
r
VPGT 110302CF 0.2
Minute ap E30
E31
VPGT 110302F -U 0.2
Low Feed / Sharp Edge
B76 Inserts are sold in 10 piece boxes.
: Std. Item R : Std. Item (R-hand Only) L : Std. Item (L-hand Only) : Check Availability
для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru