Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-to[oClse.rurmet / Coated Carbide / Carbide]
(mm) (mm)
35°Diamond • Positive with Hole Description A T d Description A T d
VC_0802_ 4.76 2.38
VC_1103_ 6.35 3.18 2.3 7 VC_1604_ 9.525 4.76 4.4 7
CVD Coated Carbide 2.8 7 VC_2205_ 12.70 5.56 5.5 7
P Free-cutting steel B
Classication of usage
r Positive
T Carbon Steel and Alloy Steel : Interruption / 1st Choice Insert
M Stainless Steel
Description :Interruption / 2nd Choice $
Gray Cast Iron %
A K :Light Interruption / 1st Choice 3
d Nodular Cast Iron 4
:Light Interruption / 2nd Choice 5
TN6010N 7
35 TN6020 Non-ferrous Metals :Continuous / 1st Choice 8
S Heat-resistant alloy :Continuous / 2nd Choice
Insert TN60
PV7005 Titanium Alloy (In case hardness is under 45HRC)
Handed Insert PV7010
shows Left-hand PV7020H Hard Materials
CA5505
CA5515Dim.CermetPVD PVD
CA5525(mm)Cermet Coated Carbide
CA5535
CA6515r Applicable
CA6525 Chipbreaker Range
CA4010
CA4115
CA4120
CA4505
CA4515
PR930
PR1005
PR1025
PR1125
KW10 Carbide
Ref. Page for
Toolholder
VBGT 1103003 -Y 0.03 E23
110301 -Y 0.1
110302 -Y 0.2 E25
110304 -Y 0.4
110308 -Y 0.8 E27
F37
F39
VBGT 160402 -Y 0.2 F63 (mm)
160404 -Y 0.4 (Steel / Edge Length=11,16)
160408 -Y 0.8
E23 4
E25 Insert (Turning)
Finishing-Medium F37 3ap Y (16)
F39
F63
2
VBGT 1103005M -Y < 0.05 E23
110301M -Y < 0.1
110302M -Y < 0.2 E25 1 Y (11)
110304M -Y < 0.4 E27
110308M -Y < 0.8
F37 F / FSF
F39 0.1 0.2 0.3 0.4
F63 f (mm/rev)
VBGT 160402M -Y < 0.2 E23
160404M -Y < 0.4
160408M -Y < 0.8 E25
F37
F39
F63
Finishing VCMT 080202VF 0.2 E27 (mm) (Steel)
080204VF 0.4 F37 4
F39
VCMT 080202HQ 0.2 3
080204HQ 0.4
Finishing-Medium Refer to the table belowF632
VCMT 110304HQ 0.4 VF
ap ap HQ
1
VCMT 160404HQ 0.4 0.1 0.2 0.3 0.4
160408HQ 0.8 f (mm/rev)
VCGT 110301FN-Z 0.1
110302FN-Z 0.2
110304FN-Z 0.4
Medium / Sharp Edge
Non-ferrous Metals Non-ferrous Metals (mm) (Non-ferrous Metals)
4
VCGT 160404AH 0.4
Finishing-Medium / Sharp Edge 3
AH
VCGT 160404 -A3 0.4
160408 -A3 0.8 2
Finishing-Medium / Sharp Edge 1 A3
0.1 0.2 0.3 0.4
f (mm/rev)
VCGT 160412 1.2
Non-ferrous Material VCGT 220530 3.0 -
Medium-Roughing
Insert whose corner R(r) dimension expressed with less than sign (e.g. <0.05, <0.1, <0.2 etc.) indicate models with minus tolerance for corner R(r).
Description Ref. Page for Toolholder
VC..11 type E23,E25,E27,F37,F39,F63
VC..16 type E23,E25,F37,F39,F63
For grades TN30 PV60 PR905 , See Page B77
PV30 PV90 PR915
B67Inserts are sold in 10 piece boxes.
: Std. Item : Check Availability R : Std. Item (R-hand Only) kyLo:cSetrda.@Itekmyo(Lc-ehraan-dtoOonlsly.)ru
www.kyocera-tools.ru