Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru
Turning Indexable Inserts
35°Diamond • Positive with Hole (mm)
Description A T d
VB_1103_ 6.35 3.18 2.8 5
VB_1604_ 9.525 4.76 4.4 5
B P Free-cutting steel
Classication of usage
Positive r
Insert Carbon Steel and Alloy Steel : Interruption / 1st Choice
35 M Stainless Steel
$ T :Interruption / 2nd Choice
% Gray Cast Iron
3 A d K :Light Interruption / 1st Choice
4
5 Nodular Cast Iron :Light Interruption / 2nd Choice
7
8 N Non-ferrous Metals :Continuous / 1st Choice
S Heat-resistant alloy : Continuous / 2nd Choice
Titanium Alloy
H Hard Materials (In case hardness is under 45HRC)
PVD
Coated Carbide
Dim. TN6010CermetPVD
(mm) TN6020Cermet
TN60
PV7005
PV7010
PV7020
CA5505
CA5515
CA5525
CA5535
CA6515
CA6525
CA4010
CA4115
CA4120
CA4505
CA4515
PR930
PR1005
PR1025
PR1125
KW10 Carbide
Ref. Page for
Toolholder
CVD Coated Carbide
Insert Description r Applicable
Chipbreaker Range
Handed Insert VBMT 110304GP
shows Left-hand
0.4 E23
~E27
F37 (mm)
F39 (Steel / Edge Length=11)
F63
3
E23
Insert (Turning) VBMT 160404GP 0.4 F37 ap 2 HQ
Finishing 160408GP 0.8 F39
F63 VF
0.2 1
0.4 E23
VBMT 110302VF 0.8 ~E27 GP 0.4
110304VF F37 0.1 0.2 0.3
110308VF 0.2 F39
0.4 F63 f (mm/rev)
0.8
VBMT 160402VF 1.2 E23
160404VF F37
160408VF 0.4 F39 (mm) (Steel / Edge Length=16)
160412VF 0.8 F63 3
VBMT 110304HQ 0.4 E23 ap HQ
110308HQ 0.8 ~E27 2
Finishing-Medium 1.2 F37
F39 VF
F63 1
VBMT 160404HQ E23 GP 0.4
160408HQ F37 0.1 0.2 0.3
160412HQ F39
F63 f (mm/rev)
VBGT 110301FN-Z 0.1
110302FN-Z 0.2
Medium 110304FN-Z 0.4
110308FN-Z 0.8
Sharp Edge
VBGT 1103003 -F 0.03
Finishing VBGT 110301 -F 0.1 E23 ap(mm)
VBET 110302 -F 0.2 E25 (Steel / Edge Length=11,16)
1103005M -F E27
110301M -F < 0.05 F37 4
110302M -F < 0.1 F39
1103003 FSF < 0.2 F63 3
0.03 Y (16)
2
Super Fine
VBET 110301 FSF 0.1 1 Y (11)
110302 FSF 0.2
1103005M -FSF < 0.05 F / FSF
110301M -FSF < 0.1 0.1 0.2 0.3 0.4
f (mm/rev)
Sharp Edge / Precision 110302M -FSF < 0.2
Insert whose corner R(r) dimension expressed with less than sign (e.g. <0.05, 0.1, <0.2 etc.) indicate models with minus tolerance for corner R(r).
For grades TN30 PV60 PR905 , See Page B77
PV30 PV90 PR915
Inserts are sold in 10 piece boxes.
B66 : Std. Item : Check Availability R : Std. Item (R-hand Only) kyLo:cSetrda.@Itekmyo(Lc-ehraan-dtoOonlsly.)ru
www.kyocera-tools.ru