Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru
Slot Mill Lay-down type / Half Side Slot Mill
Recommended Cutting Conditions (For CA0835 / PR0725) fz (mm/t)
Recommended Insert Grade (Cutting Speed Vc: m/min) Chipbreaker
Workpiece Material Hardness CVD Coated Carbide PVD Coated Carbide ER-SB Remarks
EL-SB
(HB) EN-SD 0.10-0.22 SN-SB
ER-SD 0.10-0.22 SR-SB
CA0835 PR0725 EL-SD 0.10-0.22 SL-SB
0.07-0.20 0.10-0.22
Low Carbon St42-2 125 250-310 170-210 0.07-0.20 0.08-0.20 0.15-0.3
Steel C10E~C25 100-140 0.07-0.20 0.08-0.20
0.07-0.20 0.08-0.20
C30~C60 190 160-190 90-120 0.05-0.18 0.08-0.20 0.15-0.3
(Annealed) 250 140-180 90-120 0.05-0.18 0.08-0.20
Carbon Steel 80-110 0.05-0.18 0.08-0.20
C30~C60 70-90 0.05-0.18 0.10-0.25
(Heat treated) 110-140 0.05-0.18 0.10-0.25 0.15-0.3
100-120 0.05-0.18 0.10-0.25 0.15-0.3
15-30 0.07-0.22 Dry
20-50 0.07-0.22
Alloy Steel 34CrMo4 180 140-180 110-130 0.07-0.22
(Annealed) 275 120-160 80-100
70-90 0.12-0.25
34CrMo4
(Heat treated)
High Carbon X40CrMoV51, etc. 280 110-130 0.12-0.25
Carbide
Stainless X5CrNi1810, etc. 220 160-200 0.12-0.25
Steel X10Cr13, etc. 300 150-180
0.12-0.25
Heat-resistant 0.12-0.25 Coolant
Alloy
Inconel 718, etc. 350 -
Titanium Alloy Ti-6Al-4V, etc. 270 - 0.12-0.25
Gray Cast GG25~GG35 260 160-200 0.15-0.35
Iron
GGG40~GGG50 160 130-160 0.15-0.35 Dry
Nodular Cast
0.15-0.35
Iron
GGG60~GGG80 250 110-140
Note) 1. Use down-cut machining.
2. If ap is under 1/10 of Cutter Dia.(D), it is possible
M to increase feed per tooth(fz) 40%.
Milling
ap (Delete)
Recommended Cutting Conditions (For PR0110) fz (mm/t)
Recommended Insert Grade (Cutting Speed Vc: m/min)
Chipbreaker
Workpiece Material Hardness PVD Coated Carbide FN-SE Remarks
PR0110 FR-SE Coolant
(HB) FL-SE
Non-ferrous AlZnMgCu1.5, - 750-950 0.07-0.20
Metals G-AlSi7Mg
Note) 1. Use down-cut machining.
2. If ap is under 1/10 of Cutter Dia.(D), it is possible to increase feed per tooth(fz) 40%.
M116 kyocera@kyocera-tools.ru
www.kyocera-tools.ru