Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru
Cutting Edge Length of Plus Mill
Plus Mill M67~M69 Radius Plus Mill M133, M134
No. of Flute
Base Unit No. of InsertFront Piece Length of Front Piece Radius Front Length of
Milling
(Both Middle and End) cutting edge Clamp Bolt (Middle) Piece (End) cutting edge Clamp Bolt
Description No.ofpcs (mm) Description No.ofpcs Description No.ofpcs (mm)
6 1 25.4 HH8X35 0 1 25.6 HH8X35
MHD32-S32-A 2 10 MHD32-F 2 41.8 HH8X50 MHD32-F 1 MHD32-4RF 1 42.0 HH8X50
14 3 58.2 HH8X70 2 1 58.4 HH8X65
MHD40-S32-A 6 1 32.8 (53.8) HH8X40 01 27.2 (48.2) HH8X35
(MHD40-S32-B) 2 53.8 (74.8) HH8X65 48.2 (69.2) HH8X55
MHD40-S40-A 2 10 MHD40-F 3 74.8 (95.8) HH8X85 MHD40-F 1 MHD40-5RF 1 69.2 (90.2) HH8X80
MHD40-S42-A 14 4 95.8 (116.8) HH8X110 2 1 90.2 (111.2) HH8X100
(MHD40-S42-B)
18 31
6 1 32.8 (53.8) HH12X40 0 1 28.2 (49.2) HH12X40
2 53.8 (74.8) HH12X65
10 3 74.8 (95.8) HH12X85 1 1 49.2 (70.2) HH12X55
4 95.8 (116.8) HH12X110
MHD50-S42-A 2 14 MHD50-F 5 116.8 (137.8) HH12X130 MHD50-F 2 MHD50-6RF 1 70.2 (91.2) HH12X80
(MHD50-S42-B) 18 6 137.8 (158.8) HH12X150 3 1 91.2 (112.2) HH12X100
22 4 1 112.2 (133.2) HH12X120
26 5 1 133.2 (154.2) HH12X140
9 0 32.7 HH16X45
15 1 53.7 HH16X65
MHD63-FMA-A 3 21 MHD63-F 2 74.7 HH16X90 ---- - -
- -
27 3 95.7 HH16X110 - -
- -
33 4 116.7 HH16X130 - -
- -
9 0 32.7 HH20X40
18 1 64.2 HH20X75
MHD80-FMA-A 3 27 MHD80-F 2 95.7 HH20X110 - - - -
36 3 127.2 HH20X140
45 4 158.7 HH20X170
16 0 43.2 HH24X40
28 1 74.7 HH24X75
MHD100-FMA-A 3 40 MHD100-F 2 106.2 HH24X110 - - - -
52 3 137.7 HH24X140
64 4 169.2 HH24X170
15 1 53.7 HH16X45 M
MHD63-BT50-A 3 21 MHD63-F 2 74.7 HH16X65 ----
27 3 95.7 HH16X90
33 4 116.7 HH16X110
18 1 64.2 HH20X55
MHD80-BT50-A 3 27 MHD80-F 2 95.7 HH20X90 - - - -
36 3 127.2 HH20X120
45 4 158.7 HH20X150
28 1 74.7 HH24X60
MHD100-BT50-A 4 40 MHD100-F 2 106.2 HH24X90 - - - -
52 3 137.7 HH24X120
64 4 169.2 HH24X150
Dimension in ( ) is for Base Unit B.
Clamp Bolt Description (HH X ): …indicates screw standard (M ), …indicates bolt's nominal length (mm).
Clamp Bolt Descriptions are common to both Base Unit A and B.
Difference of Cutting Edge Length between Radius Plus Mill and Plus Mill Difference of Clamp Bolt Length in the Front Piece
As shown in Fig.1, the edge length of front piece in Radius Plus Mill (2) and the edge Radius Plus Mill's inserts protrude from the bottom of the body for the function of
length of front piece in Plus Mill (1) are different. ramping or helical milling, as well as the difference of Front Piece Length.
For this reason, the Radius Plus Mill's clamp bolt length in the front piece is
shorter than that of Plus Mill. (Fig.2)
Clamp Bolt
Long Short
Plus Mill Radius Plus Mill
Fig.1 Plus Mill Radius Plus Mill
For Radius Plus Mill and Plus Mill, Fig.2
the number of Front Piece required varies depending on the ap. When using Radius Plus Mill's front piece, be careful for the difference of clamp bolt length as
mentioned above.
If the length of clamp bolt is too long, the front piece will not be secured even when the bolt is
tightened. Make sure to check the length of clamp bolt for installation of the front piece to avoid
troubles such as tool damages.
kyocera@kyocera-tools.ru M77
www.kyocera-tools.ru