Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru
MHD Helical Endmill
No. of inserts to be installed in the Plus Mill Caution at installing Notched Insert
No. of NDK 09 type FPMT09 RPMT10 When installing Notched Insert, it is important to install it in the correct position.
Insert Type Type When it is installed wrongly, the tool cannot machine the workpiece and it
Description No. of Without With notch may damage the toolholder body.
Flute notch
N1 N2
Applicable Toolholder
Separate MHD 32-S32-SA 10 2 - 5 5 - - Description of Notched Insert
4 4 2
Type 32-S32-4RSA In case of having insert installation mark
Base Unit MHD 32-S32-A 2 2 - 11 - - NDKT 090304ER-N1 / N2 MHD25,32
Front Piece MHD 32-F 4 2 - 2 2 - - NDMM 12T308ER-N2 / N3 MHD40,50,63,80,100
32-4RF 1 1 2
MHD 20S-S20-C 3 13 - - In case of "having insert installation mark"
25-S25-C 8 2 - 44 - -
Integral 32-S32-C 10 2 - 55 Caution during insert installation
Type MHD 20-S20-4RC 3 1 1) NDMM12T308ER-N2 or -3 in the insert pocket with projection (only MHD40 / 50)
2
25S-S25-4RC 4 12 - - - 2) ND ER-N2 in the insert pocket marked
32-S32-5RC 10 2 - 44 - 2 3) ND ER-N3 in the insert pocket marked
NDMM12 type 1. How to install (MHD40, 50)
With notch
Description No. of RPMT10 RPMT12 (NDMM12T308ER-N2 Insert surface) (NDMM12T308ER-N3 Insert surface)
MHD 40-S32-SA Insert N2 N3 Type Type
No. of
Flute
Projection
40-S40-SA Projection
40-S42-SA
10 2 5 5
50-S42-SA
MHD 63-FMA-SA 21 3 7 14 - - OK OK
80-FMA-SA 27 3 9 18
OK
100-FMA-SA 40 4 20 20 With notch With notch
7 14
Separate MHD 63-BT50-SA 21 3 9 18
Type
80-BT50-SA 27 3
100-BT50-SA 40 4 20 20 (NDMM12T308ER-N2) (NDMM12T308ER-T) (NDMM12T308ER-N3)
MHD 40-S32-5RSA 4 2 - 2. How to install (MHD25, 32, 63, 80, 100)
40-S42-5RSA 10 2 4
50-S42-6RSA -2
MHD 40-S42-SB 10 2 5 5 - - How to install (NDKT090304ER-N1 / N2)
50-S42-SB -N1 will be attached except -N2
Mark
M MHD 40-S32-A Mark NDKT090304ER-N2
40-S40-A
40-S42-A 22 1 1 2
2 2
2
50-S42-A
MHD 63-FMA-A 93 3 6 Mark NDKT090304ER-N2
16 4 8 6
Base 80-FMA-A - - MHD32-F MHD25, 32 series.
(MHD25-S25-C shown)
Milling Unit 100-FMA-A
MHD 63-BT50-A 93 3 6 How to install (NDMM12T308ER-N2 / N3) NDMM12T308ER-N2
80-BT50-A 16 4 8 8 * -N3 will be attached except -N2
100-BT50-A
Mark of
MHD 40-S42-B Mark
50-S42-B
62 3 3
Mark
MHD 40-F 42 2 2
50-F
Front 63-F 6 3 2 4 - - 2
Piece 80-F 9 3 6 2
100-F
MHD 40-5RF 12 4 6 6
50-6RF
2- NDMM12T308ER-N2
-2
42 1 1 NDMM12T308ER-N2
MHD 40-S42-C 10 2 5 5 - - MHD63 80 MHD100
Integral 50-S42-C (MHD63-F shown) (MHD100-F Shown)
Type MHD 40-S42-5RC 10 2 4 4 2-
50-S42-6RC -2
Notched Insert Benets Notch
Notched Insert shows not only lowering
cutting resistance but also great effect of
chattering reduction by good approach to
workpieces.
Notched Insert
(Figure shows -N3.)
M76 kyocera@kyocera-tools.ru
www.kyocera-tools.ru