Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru
Shouldering Slotting Facing
MSR-BT50
4
4
43
43
4
4
43
43
D 100 100
0°
DrawingBT-50 Shank BT-50 Shank
S 38 Weight (kg) S 38
L 101.8 L 101.8
D Fig.2
Fig.1 0°
Toolholder Dimensions (BT50 Integral Arbor type) Spare Parts
Dimension (mm) Rake Angle (°) Shim Clamp Screw Wrench Anti-seize Compound
Std.
Description No. of Insert Clamp Screw Wrench MP-1
No. of Flute
No.of Stage D L S A.R. R.R.
MSR 063R-BT50-4 16 4 4 63 160 90 Fig.1 5.7 ---
063R-BT50-5 20 5 180 111 Fig.2 6.2
080R-BT50-4 SB-60120TR TT-25L MAP-2506 SB-40140TR DT-15
080R-BT50-5 16 4 4 80 160 90 +9° -5° Fig.1 6.9 for Insert Clamp for Shim Clamp MP-1
100R-BT50-4 20 5 180 111 Fig.2 7.4
100R-BT50-5 4 Fig.1 9.6
24 6 5 100 160 90
30 180 111 Fig.2 10.5
Shim is not available for MSR063R (Dia. D=63).
It is not recommended using only top edge part (ap = 30mm) for 4 stages / 5 stages type. If ap is small, use previous page’s 1 stage type or 2 stages type.
Deep grooving is not recommended for this cutter.
Applicable Inserts
Applicable Inserts M17
Description
3-Notched 4-Notched Low Cutting Force 3-Notched Low Cutting Force 4-Notched
MSR 063R··· M
080R···
100R··· APMT 250608ER-NB3 APMT 250608ER-NB4 APMT 250616ER-NB3P APMT 250616ER-NB4P
125R··· APMT 250616ER-NB3 APMT 250616ER-NB4
160R··· APMT 250640ER-NB3 APMT 250640ER-NB4
200R···
250R··· Milling
Caution of installing Notched Insert (No. of Inserts - Example)
“When installing Notched Insert, it is important to install it in the correct position. Description Num- No. of No. of Inserts
If it is installed in incorrect position, the tool cannot machine the workpiece and it may damage the ber of Flute With Notch
toolholder body.” Insert
For MSR Type, Notched Insert location indicator is marked at Insert installed area. NB3 NB4
33
Please be minded followings when you install Inserts to toolholders. MSR 100R-1 6 66
Indication is marked near the Insert pocket for MSR type. 12 12
100R-2 12 6
1) is for AP ER-NB3
2) is for AP ER-NB4 100R-4 24
Caution when installing the Insert with Corner-R(r) 4.0
When installing the insert with corner-radius 4.0mm, additional processing to the body is needed. Apply additional processing
to the body corner according to the chart.
Additional Processing *Round- shaped additional processing is recom-
Dimension
Insert Corner-R(r) mended.
4.0 to Body Corner
When applying chamfer shaped additional processing, Additionaly
R2.0 prosseced part
do not cut away too much. Body corner Insert with
large corner-R(r)
Pre-processing
Post-processing
: Std. Item : Check Availability R : Std. Item (R-hand Only) L : Std. Item (L-hand Only)
kyocera@kyocera-tools.ru M63
www.kyocera-tools.ru