Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru
MECX Shouldering Slotting Facing
MECX Endmill D +0 dh7 D +0
-0.2 -0.2
(Straight) S S dh7
D +0 L dh7 L
-0.2
S Fig.1 Fig.3
D +0 L
-0.2
Fig.2
dh7
S Fig.5 Fig.6
L
(Weldon) Fig.4
Toolholder Dimensions
Std. Dimension (mm) Rake Angle Drawing Spare Parts Applicable Max.
No. of Insert Clamp Screw Wrench Inserts Revolution
Description (°) Coolant
D d S A.R. R.R. Hole M16 (min-1)
(MAX)
MECX 08-S10-07-1T 1 8 10 80 16 11.7° -24.0° Fig.1 48,100
14-S12-07-2T -12.1° SB-2035TRG 44,800
2 14 12 18
17-S16-07-3T 17 -11.0° 42,400
18-S16-07-3T 3 100
Cylindrical 20-S16-07-4T 18 16 -10.9° 41,600
Standard 21-S20-07-4T 20
25-S20-07-5T 20 6 -10.4° Yes DTM-6 BDMT0703 40,200
26-S25-07-5T 4 110 16.3° Fig.3
33-S32-07-6T 21 -10.1° SB-2042TRG 39,500
20
25 -9.7° 37,000
5 120 25
26 25 -9.5° 36,500
6 33 32 130 30 -8.8° 33,100
Fine MECX 20-S16-07-5T 5 20 16 110 20 6 16.3° -10.4° Yes Fig.3 SB-2042TRG DTM-6 BDMT0703 40,200
pitch
M 25-S20-07-7T 7 25 20 120 25 -9.7° 37,000
MECX 10-S10-07-1T 1 10 10 80 17 12.8° -18.7° Fig.2 47,100
12-S12-07-2T 14.3° -13.7° SB-2035TRG 46,200
16-S16-07-3T 2 12 12 18
Standard 20-S20-07-4T
25-S25-07-5T 3 16 16 100 20 6 -11.3° Yes DTM-6 BDMT0703 43,200
32-S32-07-6T
Cylindrical 4 20 20 110 16.3° -10.4° Fig.4 SB-2042TRG 40,200
MECX 16-S16-07-4T
Milling 20-S20-07-5T 5 25 25 120 25 -9.7° 37,000
25-S25-07-7T 6 32 32 130 30 -8.9° 33,600
Standard Standard Fine pitch 4 16 16 100 20 -11.3° 43,200
5 20 20 110 6 16.3° -10.4° Yes Fig.4 SB-2042TRG DTM-6 BDMT0703 40,200
7 25 25 120 25 -9.7° 37,000
32-S32-07-8T 8 32 32 130 30 -8.9° 33,600
Cylindrical MECX 17-S16-130-07-3T 3 17 16 130 20 -11.0° 42,400
Long Shank 21-S20-140-07-4T
26-S25-160-07-5T 4 21 20 140 6 16.3° -10.1° Yes Fig.3 SB-2042TRG DTM-6 BDMT0703 39,500
33-S32-200-07-6T
5 26 25 160 25 -9.5° 36,500
MECX 16-W16-07-3T
20-W20-07-4T 6 33 32 200 30 -8.8° 33,100
25-W25-07-5T
3 16 16 68 -11.3° 43,200
20 Fig.5
4 20 20 81 6 16.3° -10.4° Yes SB-2042TRG DTM-6 BDMT0703 40,200
Weldon
5 25 25 88 25 -9.7° Fig.6 37,000
MECX 16-W16-07-4T 6 16 16 68 -11.3° 43,200
Fine 20-W20-07-5T 20 Fig.5
pitch 5 20 20 81 6 16.3° -10.4° Yes SB-2042TRG DTM-6 BDMT0703 40,200
25-W25-07-7T 7 25 25 88 25 -9.7° Fig.6 37,000
Max. Revolution
When running the endmill and cutter at the maximum revolution, the insert or holder may be damaged by centrifugal force. For more details, see “Warning” below.
For good shoulder nishes by MECX multistage ap.
In order to obtain smooth cutting wall surface by MECX multistage ap set ap within 5mm for each cut.
Warning Please observe below precautions fully. Failure to observe the precautions may cause serious damage to human body.
Warning about Max. Revolution indicated on main body Balance quality
Max. Revolution grade G
1. When running the endmill and the facemill at revolutions exceeding the maximum revolution limit, the inserts or toolholder may be (min-1)
damaged due to the centrifugal force. ISO 1940-1 / 8821
2. For actual practical revolution, please set within recommended machining condition. (JIS B0905)
3. When using at a higher revolution (over 10,000min-1), refer to the table to adjust the balance of MECX and suitable arbor.
~20 000 G16
~30 000 G6.3
30 000~ G2.5
M52 : Std. Item : Check Availability R : Std. Item (R-hand Only) L : Std. Item (L-hand Only)
kyocera@kyocera-tools.ru
www.kyocera-tools.ru