Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru CERACUT Cut-Off
Toolholder Dimensions
Std. Cut-Off Dimension (mm) Width Spare Parts Ref.Page for
Dia. (mm) Recommended
Releasing Wrench Clamp Bolt Wrench
Cutting
Description Drawing FT Conditions
R L Dmax H1=h H2 H3 B L1 L2 W H20
LTW H20
For Automatic Lathe (Long Shank Type: Self Clamp) H20
KTKH 1010K-2-125S 30 10 5 3 10 125 17.5 2.2 H20
1212M-2-150S 30 12 4 3 12 150 18.0 2.4
1616M-2-150S 36 16 - 3 16 150 20.7 Fig.1 LTK-5
1616M-3-150S
45 16 4 4 16 150 25.6 3.1
For General Cut-Off (Self Clamp)
KTKH 1010F-2S 30 10 5 4 10 80 18.6
1212H-2S
1612H-2S 33 12 4 5 12 100 19.8
1616H-2S
2012K-2S 33 16 - 3 12 100 19.8 2.2 Fig.2
2020K-2S 33 16 - 3 16 100 19.8 2.4
38 20 - 4 12 125 22.8
38 20 - 4 20 125 22.8
1612H-3S 36 16 4 4 12 100 21.7
1616H-3S
2012K-3S 36 16 4 4 16 100 21.7 Fig.2 LTK-5
2020K-3S
2525M-3S 41 20 - 5 12 125 25.3 3.1
52 20 - 5 20 125 31.0 Fig.3 H
53 25 - 5 25 150 31.5
2012K-4S 44 20 - 5 12 125 26.3 Fig.2
2020K-4S
2525M-4S 62 20 - 5 20 125 35.0 4.1 Fig.3
68 25 - 5 25 150 38.0
2525M-5S 79 25 - 5 25 150 43.5 4.8, 5.1 Fig.3 Cut-off
KTKH 2020K-3T17S 35 20 - 5 20 125 21.8 3.1
2525M-3T22S 45 25 - 5 25 150 26.8 4.1
2020K-4T22S 45 20 - 5 20 125 26.8 Fig.2 LTK-5
2525M-4T22S 45 25 - 5 25 150 26.8
For Automatic Lathe (Long Shank Type: Bolt Clamp Type)
KTKH 0808K-1.6-125B 10 8 4 2 8 125 13.0
1010K-1.6-125B
1212M-1.6-150B 20 10 2.5 2 10 125 16.8 1.6 SE-40120TR FT-15
1414M-1.6-150B 25 12 - 2 12 150 18.8
1010K-2-125B 26 14 - 2 14 150 19.8 Fig.4 -
1212M-2-150B
1616M-2-150B 20 10 5 3 10 125 16.8 2.2 SE-40120TR FT-15
1616M-3-150B 25 12 2 3 12 150 18.8 2.4
32 16 - 3 16 150 23.8
SE-50125TR LTW-20
32 16 4 4 16 150 23.8 3.1
Applicable Inserts Application Example of CERACUT Cut-Off
Ref. Page H15 1. Cut-Off after Chamfering
Insert Grooving Chamfering Cut-Off
Toolholder TKN1.6 Low Feed Lead Angle Low Feed / Lead-Angled
KTKH ...-1.6... TKN1.6-P TK 1.6 TK 1.6-P
KTKH ...-2... TKN2 TKN2-P TK 2 TK 2-P 2. Wide Grooving
KTKH ...-3... TKN2.4 TKN3-P TK 2.4 TK 3-P ~ Groove Widening
KTKH ...-4... TK 3 Traverse Finishing
KTKH ...-5... TKN3 - -
- TK 4 - (Value of “ap” shall be under the value of
TKN4 Corner-R)
TK 5
TKN4.8 ap
TKN5
(In order to prevent both corners' unequal wear)
: Std. Item : Check Availability R : Std. Item (R-hand Only) L : Std. Item (L-hand Only)
kyocera@kyocera-tools.ru H17
www.kyocera-tools.ru