Kyocera - Основной каталог 2010-2011 ENG
External Toolholders [DC для заказа - kyocera@kyocera-tools.ru Screw Clamp
, DP Insert]
SDLC-FF / SDLP-FF (Without Offset) (External / Copying)F1 F2
30° 30°
20
30 h F1 H1 B
95 95°
SDLC 1010F-11FF
0° 95° L1
SDLC 1212 -11FF
SDLP 1212F-11FF
shows above figure.
Right-hand shown
E SDLP-F (External / Copying)
F1 F2 30° 30°
20
Small Tools 30 95° Standard Corner-R(r) h F1 95° H1 B
95 0°
SDLP 1010F-11F
shows above figure. L1
Right-hand shown
Toolholder Dimensions
Std. Dimension (mm) Clamp Screw Spare Parts
Wrench
Description
R L H1=h B L1 F1 F2
SDLC 1010F -07FF 10 10 80 10
1212F -07FF
SDLC 1212H -07FF 12 12 85 12 - 0.1 SB-2570TR FT-8
1616H -07FF 12 12 100 12
SDLP
SDLP 1010F -11FF 16 16 100 16
1212F -11FF
1212H -11FF 10 10 80 10 4
1616H -11FF
1212F -11FF 12 12 85 12 2 0.1 SB-4085TR FT-15
0808F -07F
1010F -07F 12 12 100 12 2 0.2 SB-4085TR FT-15
1010F -11F 0.2 SB-2570TR FT-8
1212H -11F 16 16 100 16 -
1616H -11F 0.2 SB-4085TR FT-15
12 12 85 12 2
8 8 80 8.5 -
10 10 80 10.5
10 10 80 10.5 2
12 12 100 12.5 -
16 16 100 16.5 -
Applicable Inserts (SDLC-FF)
Applications Minute ap Finishing Finishing-Medium Finishing-Medium Medium Medium Finishing Finishing / Precision Low Feed Finishing / Precision
Ref. Page B50 B50 B51 B51 B52 B51 B53 B54
B53 B54
Insert CF GF GK GQ FN-Z Standard -F F -USF
-FSF (E / F) -U
Toolholder DCGT0702.. DCGT0702.. DCMT0702.. DCGT0702.. DCGT0702.. DCGT0702.. DCGT0702.. DCET0702.. DCGT0702.. DCET0702..
SDLC ...-07FF DCGT11T3.. DCGT11T3.. DCMT11T3.. DCGT11T3.. DCGT11T3.. DCGT11T3.. DCGT11T3.. DCET11T3.. DCGT11T3.. DCET11T3..
SDLC ...-11FF DCMT11T3..
Applications Low Feed Low Feed / Precision Low Carbon Steel Finishing Low Carbon Steel Stainless Steel Cast Iron Non-ferrous Metals Non-ferrous Metals Non-ferrous Metals Hard Materials
Ref. Page Finishing-Medium
Insert B55 B55 B52 B52 B52 B55 B55 B55 C19 C11
(E / F) -J F -JSF XP XQ MQ Without Chipbreaker AH -A3 PCD CBN
Toolholder - - DCMT0702.. - DCMT0702.. DCGW0702.. - - DCMT0702.. DCMW0702..
DCGT11T3.. DCET11T3.. DCMT11T3.. DCMT11T3.. DCMT11T3.. DCGW11T3.. DCGT11T3.. DCGT11T3.. DCMT11T3.. DCMW11T3..
SDLC ...-07FF
SDLC ...-11FF
Applicable Inserts (SDLP-F) (SDLP-FF)
Applications Finishing / Precision Low Feed / Precision
Ref. Page B56 B56
Insert
-FSF F -USF
Toolholder DPET0702.. DPET0702..
DPET11T3.. DPET11T3..
SDLP ...-07F
SDLP ...-11F/-11FF
For recommended cutting conditions, see page E30~E31
: Std. Item : Check Availability R : Std. Item (R-hand Only) L : Std. Item (L-hand Only)
E16 kyocera@kyocera-tools.ru
www.kyocera-tools.ru