Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru
Recommended Cutting Conditions
Recommended Cutting Conditions - External Turning (Negative Insert) (ap indicates radius)
ISO Workpiece Cutting Recommended Recommended Corner-R Lower Limit - Recommendation - Upper Limit
Classication Material Range Chipbreaker Grade (r)
Hardness Application
vc(m/min) ap(mm) f(mm/rev)
Finishing Continuous HQ TN6020 0.8 120 - 160 - 200 0.5 - 1.0 - 1.5 0.08 - 0.15 - 0.2
TN6020 0.8 100 - 120 - 150 0.5 - 1.0 - 1.5 0.05 - 0.1 - 0.15
(Gloss Oriented) Interruption
Finishing Continuous MQ CA6515 0.4 120 - 180 - 240 0.5 - 1.0 - 1.5 0.08 - 0.15 - 0.2
Interruption CA6525 0.8 100 - 160 - 220 0.5 - 1.0 - 1.5 0.05 - 0.1 - 0.15
HB Medium-Roughing Continuous
D Stainless 220 (Chip Control Oriented) Interruption MS CA6515 0.4 120 - 160 - 200 1.0 - 2.0 - 3.0 0.1 - 0.2 - 0.3
MU CA6525 0.8 80 - 140 - 180 1.0 - 2.0 - 3.0 0.2 - 0.3 - 0.4
Steel Medium-Roughing Continuous CA6515 0.4 120 - 160 - 200 1.0 - 2.0 - 3.0 0.15 - 0.25 - 0.35
(Sharpness Oriented) Interruption CA6525 0.8 80 - 140 - 180 1.0 - 2.0 - 3.0 0.15 - 0.25 - 0.3
M Roughing Continuous CA6515 0.8 100 - 140 - 180 1.0 - 2.0 - 4.0 0.2 - 0.3 - 0.4
K CA6525 1.2 80 - 120 - 150 1.0 - 2.0 - 4.0 0.2 - 0.3 - 0.4
Interruption Standard
External Finishing Continuous HQ TN6020 0.8 100 - 120 - 150 0.5 - 1.0 - 1.5 0.05 - 0.1 - 0.15
(Gloss Oriented) Interruption TN6020 0.8 80 - 100 - 120 0.5 - 1.0 - 1.5 0.05 - 0.08 - 0.1
Finishing Continuous MQ CA6515 0.4 100 - 120 - 150 0.5 - 1.0 - 1.5 0.08 - 0.15 - 0.2
Interruption MS CA6525 0.8 80 - 100 - 120 0.5 - 1.0 - 1.5 0.05 - 0.1 - 0.15
HB Medium-Roughing Continuous MU CA6515 0.4 100 - 120 - 150 1.0 - 1.5 - 2.0 0.1 - 0.15 - 0.25
Stainless CA6525 0.8 80 - 100 - 120 1.0 - 2.0 - 3.0 0.1 - 0.15 - 0.2
Steel 300 (Chip Control Oriented) Interruption CA6515 0.4 100 - 120 - 150 1.0 - 1.5 - 2.0 0.1 - 0.15 - 0.25
Medium-Roughing Continuous CA6525 0.8 80 - 100 - 120 1.0 - 2.0 - 3.0 0.1 - 0.15 - 0.2
Gray Cast
Iron (Sharpness Oriented) Interruption
Roughing Continuous CA6515 0.8 80 - 100 - 120 1.0 - 2.0 - 3.0 0.2 - 0.3 - 0.4
CA6525 1.2 60 - 80 - 100 1.0 - 2.0 - 4.0 0.2 - 0.3 - 0.4
Interruption Standard
High Speed Continuous Without KBN60M 0.8 400 - 700 - 900 0.05 - 0.2 - 0.5 0.03 - 0.05 - 0.1
Cutting Continuous Chipbreaker KBN900 1.2 500 - 900 -1200 0.1 - 0.5 - 1.0 0.05 - 0.1 - 0.2
Interruption KBN900 1.2 500 - 700 - 900 0.5 - 1.0 - 1.5 0.05 - 0.1 - 0.2
Finishing Continuous PV7005 0.8 300 - 350 - 400 0.5 - 1.0 - 1.5 0.1 - 0.2 - 0.3
(Gloss Oriented) TN6020 0.8 100 - 150 - 200 0.5 - 1.0 - 1.5 0.08 - 0.15 - 0.2
Interruption Standard
HB Finishing Continuous KA30 1.2 300 - 500 - 700 0.3 - 0.5 - 1.0 0.1 - 0.2 - 0.3
(Ceramic) Interruption Without PT600M 0.8 300 - 450 - 600 0.3 - 0.5 - 1.0 0.1 - 0.2 - 0.3
250 Medium Continuous Chipbreaker KS6000 1.2 250 - 400 - 500 1.0 - 2.0 - 3.0 0.15 - 0.25 - 0.35
KS6000 1.2 250 - 400 - 500 1.0 - 2.0 - 3.0 0.15 - 0.2 - 0.3
(Ceramic) Interruption
Medium Continuous CA4010 0.8 200 - 250 - 300 0.5 - 2.0 - 2.5 0.1 - 0.2 - 0.3
CA4010 1.2 150 - 200 - 250 0.5 - 2.0 - 2.5 0.08 - 0.15 - 0.2
Interruption Standard
Roughing Continuous ZS CA4010 0.8 200 - 250 - 300 1.0 - 2.0 - 4.0 0.2 - 0.3 - 0.4
Interruption CA4010 1.2 150 - 200 - 250 1.0 - 2.0 - 4.0 0.2 - 0.3 - 0.4
High Speed Continuous Without KBN60M 0.4 200 - 300 - 400 0.1 - 0.3 - 0.5 0.1 - 0.15 - 0.2
Cutting Interruption Chipbreaker PT600M 0.8 200 - 250 - 350 0.1 - 0.5 - 1.0 0.1 - 0.2 - 0.4
0.8 150 - 250 - 300 0.5 - 1.0 - 1.5 0.1 - 0.2 - 0.3
Nodular Cast HB Finishing Continuous PV7005 0.8 100 - 150 - 180 0.5 - 1.0 - 1.5 0.08 - 0.15 - 0.2
(Gloss Oriented) Interruption Standard TN6020
Iron 270 Medium Continuous CA4115 0.8 150 - 200 - 250 0.5 - 2.0 - 2.5 0.1 - 0.2 - 0.3
CA4120 1.2 120 - 180 - 220 0.5 - 2.0 - 2.5 0.08 - 0.15 - 0.2
Interruption Standard
Roughing Continuous ZS CA4115 0.8 150 - 200 - 250 1.0 - 2.0 - 4.0 0.2 - 0.3 - 0.4
Interruption CA4120 1.2 120 - 180 - 220 1.0 - 2.0 - 4.0 0.2 - 0.3 - 0.4
High Speed Cutting Continuous Without KPD001 0.4 300 - 800 -2000 0.05 - 0.5 - 1.0 0.05 - 0.1 - 0.15
(Rainbow Surface Gross) Chipbreaker
N Non-ferrous HB
Metals 100 Finishing Continuous A3 KW10 0.8 400 - 500 - 700 0.5 - 1.0 - 2.0 0.1 - 0.2 - 0.25
Medium Interruption AH KW10 0.8 400 - 500 - 700 0.5 - 1.0 - 2.0 0.1 - 0.2 - 0.25
Continuous KW10 0.8 200 - 300 - 500 1.0 - 2.0 - 3.5 0.1 - 0.3 - 0.4
Interruption KW10 0.8 200 - 300 - 500 1.0 - 2.0 - 3.5 0.1 - 0.3 - 0.4
Precision Cutting Continuous Without KPD001 0.4 100 - 150 - 180 0.05 - 0.3 - 0.5 0.03 - 0.1 - 0.15
0.4 70 - 120 - 150 0.05 - 0.3 - 0.5 0.03 - 0.07 - 0.1
HB (Rainbow Surface Gross) Interruption Chipbreaker KPD001 0.4 30 - 50 - 70 0.5 - 1.5 - 2.5 0.07 - 0.15 - 0.25
0.4 30 - 50 - 70 0.5 - 1.5 - 2.5 0.07 - 0.15 - 0.2
Titanium Alloy Finishing Continuous A3 KW10 0.8 30 - 50 - 70 1.0 - 2.0 - 3.5 0.1 - 0.25 - 0.35
Interruption KW10 0.8 30 - 50 - 70 1.0 - 2.0 - 3.5 0.1 - 0.2 - 0.3
400
Medium Continuous AH KW10
S Interruption KW10
Heat-resistant HB Finishing Continuous MQ CA6515 0.4 40 - 60 - 80 0.2 - 0.5 - 1.0 0.03 - 0.08 - 0.12
Interruption Standard CA6525 0.8 40 - 60 - 80 0.2 - 0.5 - 1.0 0.05 - 0.1 - 0.15
Alloys CA6515 0.8 40 - 60 - 80 0.5 - 1.0 - 2.0 0.05 - 0.1 - 0.15
350 Medium Continuous MS 40 - 60 - 80 0.5 - 1.0 - 2.0 0.1 - 0.15 - 0.2
Interruption Standard CA6525 1.2
CA5515 0.8 60 - 100 - 120 0.1 - 0.3 - 0.5 0.05 - 0.08 - 0.1
40 50 Finishing Continuous HQ 30 - 50 - 70 0.1 - 0.3 - 0.5 0.05 - 0.08 - 0.1
HRC
Interruption Standard CA5515 0.8
Continuous Without PT600M 0.8 60 - 80 - 100 0.2 - 0.5 - 0.7 0.05 - 0.1 - 0.15
H Hard 40~50 HRC Finishing Interruption Chipbreaker PT600M 1.2 30 - 40 - 60 0.2 - 0.5 - 0.7 0.05 - 0.1 - 0.15
Materials 50~65 HRC Finishing Continuous Without Chipbreaker KBN10M 0.8 100 - 150 - 200 0.05 - 0.3 - 0.5 0.05 - 0.08 - 0.1
Interruption SET,MET KBN25M 1.2 80 - 120 - 160 0.05 - 0.3 - 0.5 0.05 - 0.08 - 0.1
50~68
HRC Medium Continuous Without KBN900 1.2 80 - 100 - 120 0.5 - 1.0 - 2.0 0.05 - 0.1 - 0.2
Interruption Chipbreaker KBN900 Radius Plus 70 - 90 - 110 0.3 - 0.7 - 1.0 0.05 - 0.1 - 0.15
D40 kyocera@kyocera-tools.ru
www.kyocera-tools.ru