Ниже представлена эта же страница в формате, позволяющем производить копирование текста.

Kyocera - Каталог Токарный инструмент 2016 ENG

                                                                           для заказа - kyocera@kyocera-tools.ru

GUIDE OF CUT-OFF

 T ool Selection                                                                                               Small Diameter        KGD             KGM            KTKB / KTKH      GRADES                   A
                                                                                                                      Cut-Off                                                                                   B
           1. Insert's Edge NumberInsert                                                                                                 -                -                           INSERTS                  C
                              1-edge Insert··· For Larger Dia. Workpiece (Max. 4.724" / 120mm)                            -                                                  -                                 D
                              2-edge Insert··· For Smaller Dia. Workpiece Cost per corner is reduced                                                                      TKN        CBN & PCD                E
                                                                                                                                      GDM                                  TK§                                 F
           2. Use a neutral angle insert if there is no restriction to the size of boss left on part.                 TKF...S         GDMS             GMM                 (Fig. 1)                             G
           (See Fig.3 Below)                                                                                         TKF...NB        GDM-§           GMM-§                    -                                 H
                                                                                                                     TKFS...S         (Fig. 2)        (Fig. 2)                                                 J
           3. Use an angled insert to reduce the size of the remaining boss.                                         TKF...DR                        GMM-§
           4. Use a sharp-cornered lead-angled insert to make the remaining boss much smaller                        TKF...DR            -            (Fig. 2)
           when machining small parts and thin parts.                                                                                    
           5. Use the minimum width insert suitable for the machining.                                                                                  

Tololholder      1. Use a suitable toolholder (blade) for the workpiece dia.                                          

                 2. Use a more rigid toolholder (blade).                                                                                                                           TOOLHOLDERS SMALL TOOLS

                 3. Use a side screw or self clamp toolholder if there is no space for clamping tools from                          -                      -                -
                 top side (for small tools).

 H ow to Select Cut-Off Inserts

                 1) Use a neutral angle insert, when remaining boss is not a concern. (See Fig.1)                                                                                      BORING
                 2) Use an angled insert to reduce the remaining boss. (See Fig.2)
                 3) Use a sharp-edged insert with lead angle to minimize the remaining boss when cutting small parts and thin parts. (See Fig.3)

                     N             RL                                                       With Lead Angle      Without Lead Angle
                 (Neutral)  (Right-Hand) (Left-Hand)                                          (Right-Hand)              (Neutral)

Lead Angle Hand                                                                             TTTKKTKRKRRR              TTTKKTKNKNNN                                                     GROOVING

                                                        

                                                                                                                                                                Bigger Boss

                 • Angled () insert can reduce burr when cutting off.     Lead Angle Hand                                                                                             CUT-OFF
                 • When using a larger lead angle (), cutting resistance
                                                                                            TTTKKTKRKRRR              TTTKKTKNKNNN
                   becomes smaller. The feed rate should be reduced.
                                                                                                                                                                                       THREADING
                                 Fig.1

                                                                                                                                        Sharp Edge                    With Lead Angle  HSK TOOLING SPARE PARTS  N
                                                                                                                                                                                                                P
 Caution                                                                                                Fig.2                                                Fig.3

1) Set the cutting edge height 0.004"-0.008" above the center height

2) Always apply sufficient coolant to the cutting edge                                                                                                                                 TECHNICAL

3) Constant spindle revolution is recommended to obtain stable tool life                                                                Edge Height                                                             R
                                                                                                                                                                                                                T
4) Cut-off as close to the chuck as possible

5) Decrease the feed rate from 1/2 to 1/3 when diameter is same as cut-off width                                                                               Workpiece               INDEX

• Overuse of insert and toolholder (blade) may cause insert breakage and                                                                             Fig.4
  toolholder (blade) damage.

• Do not rework the insert and toolholder (blade) to prevent damage

• Clean the insert pocket well with compressed air when replacing insert

                                                                                            kyocera@kyocera-tools.ru                                                                   H3
                                                                                               www.kyocera-tools.ru
Заявка