для заказа - kyocera@kyocera-tools.ru
PRODUCT LINEUP
P roduct Lineup
Small Diameter KTKF ( H8 ) KTKFS ( H10 )
Cut-Off
Small Sub Spindle Tooling
Diameter Cut-Off Diameter Cut-Off Diameter
Cut-Off 0.197"~0.472" 0.236"~0.472"
0.551"~0.630"
~0.630" Width : (0.020"~0.079") (6mm~12mm) Width : (0.039"~0.079")
(5mm~12mm) Width : (0.5mm~2.0mm) (14mm ~16mm) Width : (1.0mm~2.0mm)
(~16mm) Sub Spindle Tooling
Cut-Off Diameter
KGD ( H14 ) KGD-S ( H17 ) 0.236"~0.472" KGDS ( H15 )
0.551"~0.630"
KGD Bolt Clamp (6mm~12mm)
Cut-Off Diameter (24mm)
0.472"~1.575"
(12mm~50mm)
Width : (0.079"~0.158") Width : (0.079"~0.158") Width : (1.3mm~3.0mm)
Width : (1.3mm~4.0mm) Width : (1.3mm~4.0mm)
KGM ( H24 ) KGM-T ( H25 )
KGM Bolt Clamp
Cut-Off Diameter
0.709"~1.575"
(18mm~60mm)
Width : 0.059"~0.158",0.118"~0.236" Width : 0.079"~0.197"
Width : (1.5mm~4mm, 3mm~8mm) Width : (2mm~6mm)
KTKH-S ( H30 ) KTKB-S(S) ( H28 )
KTKB Toolholders Blade Type
KTKH Cut-Off Diameter Cut-Off Diameter
(1-edge Insert) 1.181"~2.441" 0.551"~0.630"
(30mm~79mm) (32mm~120mm)
CUT-OFF Width : (0.020"~0.079") Width : (0.020"~0.079")
Width : (2.2mm~5.1mm) Width : (0.5mm~2.0mm)
H C ut-Off Tools
Series Name Shape Advantage Applications
For Small 1) Insert clamp is side screw type from the side 1) For cut-off and grooving of small workpieces
Diameter 2) 2-edge insert 2) For small parts machining
Cut-Off 3) Max. Cut-off Dia. : 0.630" (16mm)
KGD 1) Insert is clamped from top side 1) PM Chipbreaker ··· For Cut-Off
2) 1-edge and 2-edge inserts available 2) PH Chipbreaker ··· For Cut-Off (High Feed Rate)
KGM 3) Integral type and separate type are available
4) Max. Cut-off Dia. : 1.969" (50mm) For Grooving
KTKB 3) PG Chipbreaker ··· For Cut-Off (for Small Parts Machining)
KTKH 1) Insert is clamped from top side
2) 1-edge and 2-edge inserts available Sharp-Cutting Oriented
3) Max. Cut-off Dia. : 2.362" (60mm) 4) PF Chipbreaker ··· For Cut-Off (for Small Parts Machining)
Low Feed
5) PQ Chipbreaker ··· For Cut-Off (for Small Parts Machining)
Medium Feed
1) For cut-off and grooving of small
workpieces
2) For automatic lathe, small machine
3) TMR-Chipbreaker provides stable chip control up to high
feed rate ranges
1) Self-Clamping System 1) For cut-off and deep grooving
Tap the insert lightly with a plastic hammer to set it in the pocket 2) Standard chipbreaker is general cut-off type
2) 1-edge insert Feed rate: over 0.004ipr
3) Blade type and Integral Shank type
4) Max. Cut-off Dia. : 4.724" (120mm) P-Chipbreaker is for cut-off at low feed rates
Feed rate: 0.001~0.003ipr
kyocera@kyocera-tools.ru
H2 www.kyocera-tools.ru