Ниже представлена эта же страница в формате, позволяющем производить копирование текста.

Kyocera - Каталог Токарный инструмент 2016 ENG

          GUIDE FOR GROOVING                                                           для заказа - kyocera@kyocera-tools.ru
                                                                                                                                        Grooving Insert with Molded Chipbreaker

           G uide for Grooving with Cermet Insert (Steel)

               1. Set the feed under 0.0047" ipr (0.0020"~0.0039" ipr normally).
               2. Coolant is recommended.
               3. Set the cutting speed Vc = 490~720 sfm.
               4. Set the toolholder overhang as short as possible.

           H ow to Improve Surface Finish (when surface roughness below 3m Rz is required)

               1. Increase the cutting speed (Vc = 720 sfm MAX.)
               2. Program retention time at the groove bottom.
               3. Apply a light hone to the cutting edge.

           C hip Control of Grooving Insert with Molded Chipbreaker

                                                   1. G ood chip control to cover wide application range stable chip control
                                                      at high cutting speed, covering wide range of feed rate

                                                   2. Improved chip control and excellent surface finish
                                                      Superior chip control performance and MEGACOAT PR1215 realizes the excellent surface quality

                                                   3. C hip control improvement at automated production line.
                                                      (prevent frequent machine stop)

                                                   GBA type GM chipbreakerGROOVING

                      Multi Bump Design

G Center bump and dent squeeze chips for better control.

                                                                                                        Helps modifying chip shape.

                                                                                                       Stable chip control during shouldering and chamfering.

                                                                                                       Front Bump: Stabilize chip control at low feed rates.

          Smooth chip control due to optimized bump design of the chipbreaker

           A lternative Toolholder Reference Table for Grooving Toolholder

                                     Conventional Toolholder                                                                                       Alternative Toolholder

                                                                                       Spare Parts

                                     Overall  Clamp Screw                              Wrench       Wrench                                         Overall
                                     length                                                                                                        length
          Part Number                 (mm)                                                                           Part Number                    (mm)                   Notes  Reference
                                                                                                                                                                                     Page
          KTGF§ 1010K-16F            125                                                                     KTGF§ 1010JX-16F                      120
                                                                                                                                                   120                             G12
          1212M-16F                  150 SB-4070TRW                                    FT-8         -                                  1212JX-16F  120
                                                                                                                                                                                   G36
          1616M-16F                  150                                                                                               1616JX-16F   - No replacement
                                                                                                                                                   120
          KGM§ 0810K-1.5-125         125                                                                                               -           120

          1010K-1.5-125              125 SE-40120TR                                    -            LTW-15S  KGM§ 1010JX-1.5                        - No replacement
                                                                                                                                                   120
          1212M-1.5-150              150                                                                                               1212JX-1.5  120
                                                                                                                                                   120
          KGM§ 0810K-2-125           125                                                                                               -           120
                                                                                                                                                   120
          1010K-2-125                125 SE-40120TR                                    -            LTW-15S  KGM§ 1010JX-2                         120
                                                                                                                                                   120
          1212M-2-150                150                                                                                               1212JX-2

          1616M-2-150                150 SE-50125TR                                    -            LTW-20                             1616JX-2

          KGM§ 1010K-2.5-125         125      SE-40120TR                               -            LTW-15S  KGM§ 1010JX-2.5
                      1212M-2.5-150  150                                                                                 1212JX-2.5

          1616M-2.5-150              150 SE-50125TR                                    -            LTW-20                             1616JX-2.5

          KGM§ 1616M-3-150           150 SE-50125TR                                    -            LTW-20   KGM§ 1616JX-3

          Note) The corresponding replacements may be different from the conventional parts in insert clamping system or insert size.

          Make sure their specifications referring to the catalog or other documents.

                                                                                             kyocera@kyocera-tools.ru

G132                                                                                           www.kyocera-tools.ru
Заявка