Ниже представлена эта же страница в формате, позволяющем производить копирование текста.

Kyocera - Каталог Токарный инструмент 2016 ENG

                                                                                              для заказа - kyocera@kyocera-tools.ru%') #
                                                    	'BDF(SPPWJOH%JB
                             8
                      FACE GROOVING TOOLHOLDERS
                                                                                                  )
                       KFMS-8

                                                                                                                          5
                                                                                                                                                   -

                                                                                                                            -

                                                                                                  I

                                                                                                  )

                                                   5                                                                                              • Left-hand shown

                                                                     • Right-hand shown

                       T oolholder Dimensions

                                                                                Stock                            Dimensions (mm)                                      Face Grooving                      Spare Parts
                                                                                R L H1=h H2                      B L1 L2                                                  Dia. D
                                                                                                                                                                                           Clamp Bolt            Wrench

                      Part Number

                                                                                                             H3                         F T W MIN MAX

                      KFMS§ 2525M5464-8                                           25                   -   9   25 150 41 26 25                          8           54 64
                                   2525M6382-8                                    25                  2.4  9   25 150 41 26 25                                      (0) ()
                                   2525M80115-8                                   25                  6.0  8   25 150 40 26 25
                                   2525M105160-8                                  25                  6.0  8   25 150 40 26 25                          8           63 82
                                                                                                                                                                      (0) ()

                                                                                                                                                          8           80 115
                                                                                                                                                                      (0) ()
                                                                                                                                                                                                         HH6X25       LW-5
                                                                                                                                                                      105 160
                                                                                                                                                          8           (0) ()

                      2525M155510-8                                               25                  6.0  8   25 150 43 26 25                          8 155 510
                      3232P155510-8                                              32                     -   8   32 170 43 33 25                          8 (0) ()

G           GROOVING  •	 Dimension T shows available grooving depth.
                      •	 The value ( ) of Face Grooving Dia. (D MAX.) is the maximum outer diameter value after the initial groove between MIN.~MAX. (It is possible to widen the groove to infinity ).
  EXTERNAL
   INTERNAL             The value ( ) of Face Grooving Dia. (D MIN.) is the minimum diameter of the boss which remains in the center when widening the groove width to a smaller value after the initial groove between

        FACE          MIN.~MAX..

                       A pplicable Inserts                                                                     P Carbon Steel / Alloy Steel                                

                         Part Number                    L                          (mm)                          M Stainless Steel                                           
                      GMM 8030-080MW                    30                           H                           K Cast Iron                                                         Classification of Usage
                      GMG 8030-050MG                    30                                                       N Non-ferrous Metals
                      GMGA 8030-400R                    30                          5.5                          S Titanium Alloy                                                                         : Light Interruption / 1st Choice
                                                                                    5.5
                                                                                    5.5                                  Hard materials (40HRC)                                            : Light Interruption / 2nd Choice
                                                                                                                 H                                                                          : Continuous / 1st Choice
                                                                                                                                                                               : Continuous / 2nd Choice
                                                                                                                         Hard materials (40HRC)

                                                                                                                   Previous       Dimensions      Cermet  CVD Coated  PVD Coated           KW10 Carbide          Applicable
                                                                                                                 Part Number          (mm)                   Carbide    Carbide                                  Toolholders

                                                Insert                                            Part Number                     W r M

                                                                                                                                                  TN90    CR9025      PR915  PR930  PR905

                                                        GMM2420-02

                                                                          M     2° 2°
                                                                                      W±0.05
                                                                                                  GMM 8030-080MW GMM 8030-08      8.0 0.8 6.0                               

                                                                          L r

                      Chip Control Oriented /                                   H
                               M Class

                                                                                              r

                                                W±0.03                                            GMG 8030-050MG GMG 8030-05MG 8.0 0.5 60                                    KFMS§…8
                                                    2° 2°

                                                                   M
                                                                             L

                      Sharp-Cutting Oriented /  15°                                8n H
                            Precision Class

                        Ground Chipbreaker

                                                        .

                                                           - S GMGA 8030-400R GMGA 8030-40R 8.0 4.0 6.0)                                                                                    

                        Sharp-Cutting Oriented /                                                                                                                           Recommended Cutting Conditions  G129
                              Precision Class                                                                                                                                         Inserts are sold in 10 piece boxes.
                             Full-R / Copying
                                                                                                                                                                                                           U.S. Stock Standard : 
                      •	 If using a full-R insert with KIGM-8 type toolholder, you need to modify the corner of insert adapter of toolholder.                         World Express (Shipping: 7-10 Business Days) : 

G120                                                                                                             kyocera@kyocera-tools.ru
                                                                                                                    www.kyocera-tools.ru
Заявка