для заказа - kyocera@kyocera-tools.ru
FACE GROOVING TOOLHOLDERS
T oolholder Dimensions
Stock Dimensions Width Face Grooving Spare Parts
B L1 L2 Dia. D Clamp Bolt Wrench
Part Number Unit GRADES A
B
RL H1=h H2 H3 F S T W MIN MAX C
- D
KFMS§ 16-5-75115 inch 1.000 - 0.393 1.000 6.000 2.012 1.027 - 1.260 0.197 2.953 4.528 HH5X25 LW-4 INSERTS E
16-5-115180 (1.047) 20 (0.236) 4.528 7.087 HH5X20 LW-4 F
16-5-180235 - 7.087 9.252 HH5X25 LW-4
25 5
KFMS§ 2020K2535-5 - 125 39 (6) 25 35
2020K3550-5 20 35 50
25 5 50 75
2020K5075-5 20 10 20 20.7 32 (6) 75 115 CBN & PCD
2020K75115-5 44 (21.2) 115 180
2020K115180-5 5 125 180 235
2020K180235-5 235
25 35
2020K235800-5 mm 35 50
2525M2535-5 50 75
39 75 115 TOOLHOLDERS SMALL TOOLS
2525M3550-5 115 180
180 235
2525M5075-5 25 - 10 25 150 44 25.7 235
2525M75115-5 (26.2)
2525M115180-5
2525M180235-5 51
2525M235800-5
• Dimension T shows available grooving depth.
• Face Grooving Dia. D: The diameter range of the initial groove.
• For KFMS§···-5 toolholder can hold a 0.236" width insert. ( ) value shows the dimension of a 0.236" width insert.
S election of Toolholder & Insert
Toolholder Right-hand (R) Toolholder Left-hand (L) BORING
Insert (No Hand) Insert (No Hand)
GROOVING G
A pplicable Inserts (in) P Carbon Steel / Alloy Steel CUT-OFF H
H M Stainless Steel Classification of Usage J
Part Number L K Cast Iron THREADING
FFMMMM~3600--0034 0.472 0.138 N Non-ferrous Metals : Light Interruption / 1st Choice
FFMM~NN36 S Titanium Alloy : Light Interruption / 2nd Choice
0.472 0.138 H Hard materials (40HRC) : Continuous / 1st Choice
: Continuous / 2nd Choice
Dimensions (in) Cermet CVD Coated PVD Coated KW10 Carbide
Carbide Carbide
Applicable HSK TOOLING SPARE PARTS
Insert Part Number Toolholders N
P
W r M TN90 CR9025 PR915 PR930 PR905 R
inch mm
S FMM 30-03 0.118 3.0 0.012 0.079 KFMS§…-3(...)
m m 0.157 4.0 0.016 0.102 KFMS§…-4(...)
. 40-04
8n
. - S S 50-04 0.197 5.0 0.016 0.134 KFMS§…-5(...)
Face Grooving m ) 60-04 0.236 6.0 0.016 0.157
Chip Control Oriented / M Class S 3
8n FMN 0.118 3.0 0.010 0.079 KFMS§…-3(...)
4 0.157 4.0 0.010 0.102 KFMS§…-4(...) TECHNICAL
-5 m 0.197 5.0 0.010 0.134 KFMS§…-5(...)
Face Grooving ) 6 0.236 6.0 0.010 0.157
Sharp-Cutting Oriented / M Class
• FMN type inserts are only for Deep Grooving and not applicable for Turning. Recommended Cutting Conditions G126
Limit of Turning Toward Center It causes the toolholder to interfere with the groove wall depending on the initial cut’s diameter. INDEX T
D e.g.) KFMSR 2525M2530-3 with 25 as first cut towards the
28 center, it will cause a rubbing with the toolholder cartridge if
E Part Number 25 26 27 and over d is 4.0mm.
% KFMS§ 2020K2530-3 4 d *( ) value shows the Dimension using FMM60-04 Insert.
*OUFSGFSFODF KFMS§ 2525M2530-3 20 0
Remaining Boss Dia. d
( )KFMS§ 2020K2535-4 6 3 0 No
KFMS§ 2525M2535-4
KFMS§ 2020K2535-5 7 4 1 remaining
KFMS§ 2525M2535-5 *(5) *(2) *(0) Boss
Inserts are sold in 10 piece boxes.
: U.S. Stock Standard kyocera@kyocera-tools.ru G119
: World Express (Shipping: 7-10 Business Days) www.kyocera-tools.ru