Ниже представлена эта же страница в формате, позволяющем производить копирование текста.

Kyocera - Каталог Токарный инструмент 2016 ENG

                                                                    для заказа - kyocera@kyocera-tools.ru                                                                                                                                      Integral Toolholder

FACE GROOVING TOOLHOLDERS [GVF INSERT]

 F ace Grooving Diameter of GFV
   (1) e.g.) GFV§…-201A

                               Part Number                           Face Grooving                                                       Applicable Inserts  •	It is available to infinity  in case of machining the first                                         GRADES                   A
                                                                         Dia. D                                                                               groove bigger than MIN.                                                                                                       B
                                                                                                                                                                                                                                                                                             C
GFV§ 2020K-201A                                                      MIN MAX                                                                                 •	When machining towards the outer diameter then
                                                                      20  GVF§200~340-020A                                                                    there is no MAX. limit to the further groove machining.

                                              2525M-201A             (12) () GVF§200-…~300-…AR                                                              •	When widening the groove width to inner diameter.

•	When machining the initial groove on the face at MIN.20                                                                                                   Face groove diameter D MIN. (12) is the limit; the toolholder                                         INSERTS
                                                                                                                                                             interferes with the workpiece in case of smaller than 12.
If the initial groove is made smaller than this, the toolholder interferes with the workpiece. The toolholder interferes with the workpiece when closer to
Boss Dia. depends on insert width.                                                                                                                           the center.

 	.*/'BDF(SPPWJOH%JB
                                        	.*/'BDF(SPPWJOH%JB
                                                               	.*/'BDF(SPPWJOH%JB
                   	.*/'BDF(SPPWJOH%JB
                                  CBN & PCD
      NN	8JEUI
                                                       	#PTT%JB
                                                                             	.JOCPTT%JB
                            	.JOCPTT%JB


           	#PTT%JB
                                                                                                                                                                                                                                     TOOLHOLDERS SMALL TOOLS
                                                                                                                                                                                                       

                                                                                                                                                                   NN                                   NN                                                                                 D

                                                                     NN	8JEUI
                                                                                     	8JEFOJOHUIFHSPPWF                 	8JEFOJOHUIFHSPPWF
                                                                                                                                                                           XJEUIUPDFOUFS
          XJEUIUPDFOUFS


Installing GVFR200-020A Installing GVFR340-020A                                                                                                              Installing GVFR200-020A Installing GVFR340-020A                                                                                 E
                                                                                                                                                                                                                                                                                             F
(2) e.g.) GFV§…-351B/352B (same as GFV§…-B or GFV§…-C)                                                                                                                                                                                                                                 G
                                                                                                                                                                                                                                                                                             H
                               Part Number                           Face Grooving                                                       Applicable Inserts                                                                                                         BORING
                                                                         Dia. D

GFV§ 2020K-351B                                                      MIN MAX                                                                                 •	It is possible to widen the groove to infinity  when                                                GROOVING
            2525M-351B                                                35 50 GVF§200~340-020A                                                                   machining the initial groove within MIN.-MAX. and then
                                                                                                                                                               widening to outer diameter.

                                              2020K-352B             (25) () GVF§200-…~300-…AR

              2525M-352B                                                                                                                                     •	When machining the initial groove on the face at MAX. 50mm.
•	When machining the initial groove on the face at MIN. 35                                                                                                    If the initial groove is made smaller than this, the toolholder
If the initial groove is made smaller than this, the toolholder interferes with the workpiece. interferes with the workpiece.
Boss Dia. depends on insert width.                                                                                                                           Boss Dia. depends on insert width.
                                                                                                                                                                                                                                                                    CUT-OFF

                                                                                                                                                                                                                                                        THREADING                J
    	.*/'BDF(SPPWJOH%JB
                                            	.*/'BDF(SPPWJOH%JB
                                                               	."9GBDFSPPWJOH%JB
                   	."9GBDFHSPPWJOH%JB


                                                                                                                                                                                                        
              	#PTT%JB
                                                         	#PTT%JB
                                                                            	#PTT%JB
                                	#PTT%JB


                               NN	8JEUI
                                                        NN	8JEUI
                                                  NN	8JEUI
                         NN	8JEUI
                                              HSK TOOLING SPARE PARTS  N
                                                                                                                                                                                                                                                                                             P
Installing GVFR250-020B Installing GVFR490-020B                                                                                                              Installing GVFR250-020B                     Installing GVFR490-020B                                                             R

•	When widening the groove width to inner diameter.
  Face Grooving Dia.D MIN.(25mm Boss Dia.) is the limitation regardless of insert width,
  even widening the groove width to the center from the initial groove at D MIN.(35mm) or D MAX.(50mm).
  The toolholder interferes with the workpiece when closer to the center.

                                                                                                                                                                                                                                                        TECHNICAL
    	.*/'BDF(SPPWJOH%JB
                                            	.*/'BDF(SPPWJOH%JB
                                                               	."9GBDFHSPPWJOH%JB
                    	."9GBDFHSPPWJOH%JB

                                                                                                 
                                   	.JOCPTT%JB
                                                     	.JOCPTT%JB
                                                                                       
                                                                                                                                                                           	.JO#PTT%JB
                            	.JO#PTT%JB


                               NN                                                                  NN                                                                                                                                                             INDEX                    T
                                   	8JEFOJOHUIFHSPPWF                                                	8JEFOJOHUIFHSPPWF
                                       XJEUIUPDFOUFS
                                        XJEUIUPDFOUFS
                            NN                                NN
                                                                                                                                                                      	8JEFOJOHUIFHSPPWF                  	8JEFOJOHUIFHSPPWF
                                                                                                                                                                          XJEUIUPDFOUFS
          XJEUIUPDFOUFS


Installing GVFR250-020B Installing GVFR490-020B                                                                                                              Installing GVFR250-020B Installing GVFR490-020B

                                                                                                                                         kyocera@kyocera-tools.ru                                                                              G111
                                                                                                                                            www.kyocera-tools.ru
Заявка