для заказа - kyocera@kyocera-tools.ru
FACE GROOVING TOOLHOLDERS [GVF INSERT]
GFV
5
5'PBDFP(VSUPFPWSJOEHJ%BJB
% m ' - - ) ) # 'B D5FP(SPPPVWJOUFHS%JEBJB%
-
)FB%EEJBNFUFS I )FBEEJBN%FUFS
GFV§2020K-201A -
GFV§2525M-201A
Shows Right Figure. • Left-hand shown
• Right-hand Insert for Right-hand Toolholder, Left-hand Insert for Left-hand Toolholder.
• Right-hand shown
T oolholder Dimensions
Stock Dimensions (mm) Face Grooving Spare Parts
Dia. D
Clamp Set Wrench Applicable Inserts
Part Number G116
R L H1 h H3 B L1 L2 L3 F T D1 MIN MAX LW
FT
GFV§ 2020K-201A 20 21 6.5 20 125 20 19 25 2.2 40 20 CPS-5V - FT-15 GVF§200~340-020A
2525M-201A 25 26 6.5 25 150 23 22 32 2.2 40 (12) GVF§200-…~300-…AR
GFV§ 2020K-351B 20 21 8.0 20 125 28 26 25 4.6 35 35 50 - CPS-6V LW-3 GVF§250~350-020B
2525M-351B 25 26 8.0 25 150 30 28 32 4.6 35 (25) () GVF§300-150BR
2020K-352B 20 21 8.0 20 125 28 26 25 5.1 35
2525M-352B 25 26 8.0 25 150 30 28 32 5.1 35 GVF§400~490-020B
GVF§400-200BR
G GROOVING 2020K-501B 20 21 8.0 20 125 28 26 25 4.6 50 50 70 - CPS-6V LW-3 GVF§250~350-020B
2525M-501B 25 26 8.0 25 150 30 28 32 4.6 50 (25) () GVF§300-150BR
EXTERNAL 2020K-502B 20 21 8.0 20 125 28 26 25 5.1 50
INTERNAL 2525M-502B 25 26 8.0 25 150 30 28 32 5.1 50 GVF§400~490-020B
GVF§400-200BR
FACE
2020K-701B 20 21 8.0 20 125 28 26 25 4.6 70 GVF§250~350-020B
GVF§300-150BR
2525M-701B 25 26 8.0 25 150 30 28 32 4.6 70 70 100 - CPS-6V LW-3
GVF§400~490-020B
2020K-702B 20 21 8.0 20 125 28 26 25 5.1 70 (25) () GVF§400-200BR
2525M-702B 25 26 8.0 25 150 30 28 32 5.1 70
GFV§ 2525M-501C 25 26 9.5 25 150 35 33 32 6.6 50 50 70 - CPS-8V LW-4 GVF§350~450-040C
2525M-502C 25 26 9.5 25 150 35 33 32 8.1 50 (25) () GVF§500~600-040C
2525M-701C 25 26 9.5 25 150 35 33 32 6.6 70 70 100 - CPS-8V LW-4 GVF§350~450-040C
GVF§500~600-040C
2525M-702C 25 26 9.5 25 150 35 33 32 8.1 70 (25) ()
2525M-1001C 25 26 9.5 25 150 35 35 32 6.6 100 100 150 - CPS-8V LW-4 GVF§350~450-040C
2525M-1002C 25 26 9.5 25 150 35 35 32 8.1 100 (25) () GVF§500~600-040C
2525M-1501C 25 26 9.5 25 150 35 35 32 6.6 150 150 250 - CPS-8V LW-4 GVF§350~450-040C
2525M-1502C 25 26 9.5 25 150 35 35 32 8.1 150 (25) () GVF§500~600-040C
Note 1. Dimension T shows available grooving depth.
2. D1 shows toolholder head diameter to L3.
3. The value ( ) of Face Grooving Dia. (D MAX.) is the maximum outer diameter value after the initial groove between MIN.~MAX. (It is possible to widen the groove to infinity ).
The value ( ) of Face Grooving Dia. (D MIN.) is the minimum diameter of the boss which remains in the center when widening the groove width to a smaller value after the initial groove
between MIN.~MAX.
4. S tandard toolholders are designed with the edge position 1.0mm above the centr. When using non-standard Toolholders, set the Edge position 1.0mm above the center.
S election of Toolholder & Insert
Toolholder Right-hand (R) Toolholder Left-hand (L)
Left-hand (L)
Insert Right-hand (R) Insert
G110 kyocera@kyocera-tools.ru U.S. Stock Standard :
www.kyocera-tools.ru World Express (Shipping: 7-10 Business Days) :