для заказа - kyocera@kyocera-tools.ru
RECOMMENDED CUTTING CONDITIONS
Recommended Cutting Conditions (Vc)
Recommended Insert Grade (Vc : sfm)
Workpiece Chipbreaker Cermet MEGACOAT MEGACOAT Carbide MEGACOAT CBN PCD Notes GRADES A
Material NANO CBN B
GM TN90 C
Carbon Steel GL PR1535 PR1225 PR1215 GW15 KBN05M KBN570 KPD001 INSERTS D
Alloy Steel CM E
Stainless Steel PH 330~720 - - - - Wet
Cast Iron GS 260~660 260~660 330~660 -
Aluminum GS - - - - CBN & PCD
Brass NB -
Hardened Material NB 260~660 - - - -
Powdered Steel 230~590 230~590 260~590 -
- - - -
(PH)
230~590 -
- 200~490 200~490 200~490
- - 660~1640 - 330~820 490~6560
-
- -
- 330~660
- - - 330~660 260~490 660~2620
- - - -
- - -
- - -
- - -
-
: 1st Recommendation : 2nd Recommendation TOOLHOLDERS SMALL TOOLS
Recommended Cutting Conditions (Feed Rate / D.O.C.) (Workpiece Material : 1049)
Grooving Traversing
W fW
Chipbreaker D.O.C.
BORING F
G
f : Recommended Feed H
J
GM (General Purpose) Width W (in) 0.315 0.158 W=0.315” GROOVING N
0.197~0.236 P
0.118~0.158 D.O.C. (in) 0.118 W=0.236” R
W=0.197”
<0.118
0.079 W=0.158” CUT-OFF
0.039 W=0.118”
W<0.118”
0.004 0.008 0.012 0.004 0.008 0.012 0.016
Feed Rate (ipr)
Feed Rate (ipr)
GL (Low Feed) Width W (in) 0.197~0.236 D.O.C. (in) 0.158 W=0.236” THREADING
0.118~0.158 0.118 W=0.197”
0.079 HSK TOOLING SPARE PARTS
0.095 0.039 W=0.158”
W=0.118”
W=0.095”
0.004 0.008 0.012 0.004 0.008 0.012 0.016
Feed Rate (ipr)
Feed Rate (ipr)
PH (High Feed) Width W (in) 0.118~0.158 D.O.C. (in) 0.039 * 0.0079” width is not recommended
0.079 W= 0.118”~0.158”
0.004 0.008 0.012 0.016 TECHNICAL
0.004 0.008 0.012 Feed Rate (ipr)
Feed Rate (ipr)
CM (Copying) Width W (in) 0.197~0.236 0.118 W=0.236” INDEX T
0.118~0.158 0.079 W=0.197”
D.O.C. (in) 0.039
W=0.158”
W=0.118”
0.004 0.008 0.012 0.004 0.008 0.012 0.016 0.020
Feed Rate (ipr)
Feed Rate (ipr)
1) The above values reflect a T dimension that is 0.669" (17mm) or less.
2) If the toolholder is not for the 0.315" (8mm) width insert and its T dimension is over 0.669" (17mm), set the values for longitudinal turning to less than 90% of those above.
kyocera@kyocera-tools.ru G27
www.kyocera-tools.ru