для заказа - kyocera@kyocera-tools.ru Round Shank
SWISS IQ BAR FOR MICRO BORING
S...SVN (With Side Stopper : Standard) S...SVN-N (Without Side Stopper : Standard) S...SVN-SN (Without Side Stopper : Straight)
Side Stopper H )) GRADES
D2 D1 % A
Note 2 F1 % B
L2 - - C
/PUF ' D
%- E
% F
G
/PUF ' H
Fig.1 Note 1 L1 /PUF /PUF - J
(S...SVN) N
'JH 4FUTDSFX 419
'JH 4FUTDSFX 419
INSERTS P
447//
447/4/
R
T
• Right-hand shown • Right-hand Insert for Right-hand Toolholder
Note 1 & Note 2 : See Insert Dimension Table. ( F28~F29)
T oolholder Dimensions CBN & PCD
Dimensions Spare Parts Applicable Inserts
Drawing Clamp Wrench Side Wrench Set F28~F29 TOOLHOLDERS SMALL TOOLS
Screw Stopper Screw G50
Part Number Stock Unit D1 D2 H L1 L2 F1 G78
J34
S08-SVNR12 0.500 0.787 0.480 3.500 0.906 0.157 HS3X4 VNBR....-..
inch Fig.1 SB-3080TR VNBTR....-...
S10-SVNR12 FT-10 LW-1.5 - VNGR....-..
0.625 0.945 0.584 4.000 0.906 0.236 VNFGR....-..
S12F-SVNR12N HS3X8 VNTR...-..
S14G-SVNR12N
S16H-SVNR12N 12 20.0 11 80 23 4
S19H-SVNR12N
S19N-SVNR12N mm 14 20.0 13 90 23 4 BORING
S20H-SVNR12N
S25H-SVNR12N 16 24.0 15 100 23 6
S25Q-SVNR12N
S20H-SVNR12SN 0.750 0.945 0.669 3.937 0.945 0.236 FT-10 - - SP3X4 GROOVING
S22K-SVNR12SN inch Fig.2 SB-3080TR FT-10 VNBR....-..
S25.0G-SVNR12SN VNBTR....-...
0.750 0.945 0.669 6.299 0.945 0.236 VNGR....-..
VNFGR....-..
mm 20 24.0 18 100 24 6 VNTR...-..
1.000 1.181 0.905 3.937 0.945 0.236 - - SP3X4
inch
1.000 1.181 0.905 7.086 0.945 0.236
20 19.5 18 100 23 4 CUT-OFF
mm 22 21.5 20 125 23 4 Fig.3 SB-3080TR
25 24.5 23 90 23 4
Swiss IQ Bar Selection THREADING
Gang-Type (Horizontal) Gang-Type Gang-Type Gang-Type Q: There are standard types (head dia. is larger than
(Front Loading Sleeve Type) (Back Loading Sleeve Type) shank) and straight types for round shanks.
What is each one used for? HSK TOOLING SPARE PARTS
A: The straight type is used when it cannot be
inserted from the face side of the sleeve holder
and can be inserted only from the back side due
to space limitation (Refer to Fig. below).
On the other hand, the standard type should be
installed when it can be inserted from the face side.
The head end is used for positioning as stopper.
Square Shank (Straight) Square Shank (L-Shape) Square Shank Square Shank
Round Shank (Standard) Round Shank (Standard) Round Shank (Standard) TECHNICAL
4MFFWF)PMEFS #BDLTJEF INDEX
'BDFTJEF
Round Shank (Straight) Round Shank (Straight) Round Shank (Straight) .BJO
4QJOEMF
6OBCMFUPJOTFSUBIPMEFSGSPNGBDF
TJEFCFDBVTFPGUPPOBSSPXTQBDF
Recommended toolholder may change according to machines used and actual position.
Automatic lathes have various toolpost types other than those above.
: U.S. Stock Standard kyocera@kyocera-tools.ru F31
: World Express (Shipping: 7-10 Business Days) www.kyocera-tools.ru