для заказа - kyocera@kyocera-tools.ru
EZ BAR
E ZH-HP (Sleeve) Adjustable
L2 L1 L1 GRADES
D2 L2
D1 L3 A
d1
2.5
H
D2
d1
T L4 No.1 No.3 T L4 No.1 No.3 INSERTS
No.2 No.4 No.2 No.4
(Adjustment Pin entry point: both sides) H (Adjustment Pin entry point: both sides) H B
2.5
(EZ Bars installation side) D1 (EZ Bars installation side) H
d2 d2 CBN & PCD
Fig.3 Fig.4 C
D
Dimensions (mm) T (mm) Overhang Applicable EZ Bar or E
Length of Bar 2 EZ Bar PLUS F
F16~F18 TOOLHOLDERS SMALL TOOLS G
Part Number Stock Adjustment Pin Setting Position Drawing F20~F21 H
J
d1 D1 D2 d2 H L1 L2 L3 1L4 No.1 No.2 No.3 No.4 G48, G76 N
J28
EZH 04516HP-100 4.5 16 16 6 15.0 100 4 - 25.3 Fig.3
Fig.4 _045X-…050EZ
04519HP-120 4.5 0.75" 16 6 18.0 120 18 9 25.3
04520HP-120 4.5 20 16 6 19.0 120 18 9 25.3 23.0 18.5 14.0 9.5
04522HP-135 4.5 22 16 6 21.0 135 18 9 25.3 ( 14 ) ( 9.5 ) ( - ) ( - )
04525.0HP-135 4.5 25 16 6 24.0 135 18 9 25.3
04525.4HP-120 4.5 1.00" 16 6 24.4 120 18 9 25.3
EZH 05016HP-100 5.0 16 16 6 15.0 100 4 - 29.0 Fig.3 EZBR…050… BORING
EZVBR055050-…
05019HP-120 5.0 0.75" 16 6 18.0 12 18 9 29.0 EZGR…050-…
05020HP-120 5.0 20 16 6 19.0 120 18 9 29.0 25.5 20.5 15.5 10.5 Fig.4 EZFGR…050-…
05022HP-135 5.0 22 16 6 21.0 135 18 9 29.0 EZTR…050…
3 HP…05-…
05025.0HP-135 5.0 25 16 6 24.0 135 18 9 29.0
05025.4HP-120 5.0 1.00" 16 6 24.4 120 18 9 29.0 GROOVING
EZH 06016HP-100 6.0 16 16 8 15.0 100 4 - 31.0 Fig.3 EZBR…060…
EZVBR065060-…
06019HP-120 6.0 0.75" 16 8 18.0 120 18 9 31.0 EZGR…060-…
06020HP-120 6.0 20 16 8 19.0 120 18 9 31.0 30.5 25.5 20.5 15.5 Fig.4 EZTR…060-…
_060X-…-070EZ
06022HP-135 6.0 22 16 8 21.0 135 18 9 31.0 (18.5) (13.5) ( - ) ( - ) 3 HP…0606-…
06025.0HP-135 6.0 25 16 8 24.0 135 18 9 31.0 CUT-OFF
06025.4HP-120 6.0 1.00" 16 8 24.4 120 18 9 31.0
EZH 07016HP-100 7.0 16 16 8 15.0 100 4 - 33.0 Fig.3
EZBR…070…
07019HP-120 7.0 0.75" 16 8 18.0 120 18 9 33.0
EZGR…070-…
07020HP-120 7.0 20 16 8 19.0 120 18 9 33.0 THREADING
07022HP-135 7.0 22 16 8 21.0 135 18 9 33.0 35.5 30.5 25.5 20.5 Fig.4 EZFGR…070-…
EZTR…070-…
07025.0HP-135 7.0 25 16 8 24.0 135 18 9 33.0
3 HP…07-…
07025.4HP-120 7.0 1.00" 16 8 24.4 120 18 9 33.0
1: L4 shows d1 length HSK TOOLING SPARE PARTS
2: Dimension T shows overhang length of the EZB Bar when attached to sleeve. Dimensions in ( ) show overhand length of EZ Bar PLUS.
3: HP type bars are not adjustable.
• Choose sleeves (d1) to match D dimension of bar.
E Z Bar Identification System EZ H 017 16 HP - 100
EZ Application Shank Dia. of EZB Bar Sleeve Shank Dia. Precision Overall Length of Sleeve TECHNICAL P
Symbol of Bar H-Sleeve 017 : 1.7mm 16 : 16.00mm 100 : 100mm R
025 : 2.5mm 25.4 : 25.40mm CT: High Precision 120 : 120mm T
E Z Bar Mounting Procedure with Coolant Hole
HP: ST:
Precision Standard
Bar end (Slant) Adjustment pin
How to use adjustment pin (Fig.1) Fig. 1: INDEX
How to use adjustment pin
Put the adjustment pin into the hole.
Push it into the sleeve, using the wrench “LW-1.5.” Fig. 2: Chip pocket
Tighten the clamp screw “HS3X4P” with wrench “LW-1.5” to fix the adjustment screw. How to secure bar
How to secure bar (Fig.2)
With the chip pocket upward, set the bar in sleeve.
Press the slant of the end of the bar against the adjustment pin.
Make sure that the bar does not rotate. (Fig.3)
Tighten the clamp screw with wrench “LW-2”and secure the bar.
(Use “LW-1.5” if shank dia. is 3mm or less.)
kyocera@kyocera-tools.ru Fig. 3: Clamped bar
www.kyocera-tools.ru
: U.S. Stock Standard F25
: World Express (Shipping: 7-10 Business Days)