Kyocera - Каталог фрезерование 2017 ENG
для заказа - kyocera@kyocera-tools.ru
MILLING INSERTS
Milling Inserts Usage Classification P Free-Cutting Steel
Carbon/Alloy Steel
without Hole Roughing / 1st Choice
B Roughing / 2nd Choice M Stainless Steel
Finishing / 1st Choice
Finishing / 2nd Choice K Gray Cast Iron
(Hardness Under 45HRC) Nodular Cast Iron
N Non-ferrous Metals
LINEUP / INSERTS S Heat-Resistant Alloys
Titanium Alloy
H Hard Materials
Part Number Part Number Dimensions (in) Angle (°) TN60 CVD MEGA
TN100MCermet CoatedCOAT
Insert TC60
CA6535Carbide
CA420M
(Right-hand Shown) (ANSI) (ISO) A T X Z r PR1535 MN*
PR1225
PR1210
PR830 PVD*
KW10 Carbide
Toolholder
Page
TEKN 32PTTR TEKN 1603PTTR 0.375 0.125 R0.031 0.039 - 20° 22° 30°
0.028 0.055
E69
A AA A A A 32PTFR 1603PTFR 0.375 0.125 0.028 0.055 - 20° 22° 30°
TEEN 43PTTR TEEN 2204PTTR 0.500 0.187 R0.039
Z
XX T TEKN 43PTTR TEKN 2204PTTR 0.500 0.187 R0.039 0.055 - 20° 22° 30° E48
0.028 E49
43PTFR 2204PTFR 0.500 0.187 0.028 0.055 - 20° 22° 30°
Z TEKR 43PTER-S TEKR 2204PTER-S 0.500 0.187 R0.039 0.055 - 20° 22° 30° E48
X E49
T
ZZ TEMR 32PTER-H TEMR 1603PTER-H 0.375 0.125 R0.031 0.047 E69
X - 20° 22° 30°
E48
T TEMR 43PTER-H TEMR 2204PTER-H 0.500 0.187 R0.039 0.055 E49
TPK 32PDTR TPKN 1603PDTR
1603PDFR 0.375 0.125 0.028 0.047 E49
32PDFR - 11° 15° 30°
TK 43PDTR
T TPKN 2204PDTR
2204PDFR 0.500 0.187 0.028 0.063
43PDFR
E49
Z TPKR 43PDER-S TPKR 2204PDER-S 0.500 0.187 R0.039 0.055 - 11° 15° 30°
X
T
TPMR 32PDER-H TPMR 1603PDER-H 0.375 0.125 R0.031 0.047
Z - 11° 15° 30° E49
X T TPMR 43PDER-H TPMR 2204PDER-H 0.500 0.187 R0.039 0.055
TPM 221 TPMN 110304 0.250 0.016 E49
222 110308 0.031 E69
321 160304 0.125 0.016 E49
322 160308 0.375 0.031
323 160312 0.047
T 432 220408 0.500 0.187 0.031 -
0.008
TPG 181505 TPGN 090202
-
A 18151 090204 0.219 0.094 - - 0.016 11° - -
18152 090208 0.031
r 2205 0.008
110302 E49
E69
221 110304 0.250 0.016
222 110308 0.125 0.031
321 160304 0.016
322 160308 0.375 0.031 E49
323 160312 0.047
Cutting Range Chipbreaker Features
Finishing-
Roughing S S chipbreaker for general-purpose machining. Low cutting resistance due to 13° chipbreaker rake angle.
Recommended for various depths of cut with 3-step chipbreaker design. Ground wiper edge enables
Medium- H good surface finishes.
Finishing
H chipbreaker for general-purpose machining. Smooth chip evacuation due to the chipbreaker’s smooth
rake face. 20% less cutting force than flat-top inserts due to a 25° rake angle chipbreaker.
B12 Inserts sold in 10 piece boxes. kyocera@kyocera-tools.ru U.S. Stock :
www.kyocera-tools.ru World Express (Shipping - 10 Business Days) :