Kyocera - Каталог фрезерование 2017 ENG
для заказа - kyocera@kyocera-tools.ru
MEZ-G MULTI-FUNCTION END MILL
MEZ-G End Mill Pocketing Drilling Shouldering Deep Slotting Facing
D +0 S
-0.2mm
dh7 Fig.1
S1 L
Standard
D +0 S
-0.2mm
Fig.2dh7
S1 Applicable
Inserts
Long Shank / Long Head L B20
Toolholder Dimensions Dimensions (mm) Rake Angle Spare Parts
(°)
Part Number Stock Drawing Clamp Screw Wrench
No. of Inserts
No. of Flutes D d L S A.R. R.R.
MEZ 16-S16G 4 2 16 16 120 31 16 -5° SB-2040TRG DTM-6 NDMT 080208ER-D
20-S20G 4 2 20 20 130 33 21 -4° SB-2555TRG DT-8 NDMT 10T208ER-D
25-S25G +9° Fig.1
Standard 4 2 25 25 140 40 25 -5° SB-3070TRG DT-10 NEMT 120308ER-D
MULTI-FUNCTION 32-S32G 4 2 32 32 150 50 33 -2° SB-4070TRG DT-15 NEMT 16T308ER-D
G 40-S32G 7 2 39 32 160 55 39 -3° SB-3070TRG DT-10 NEMT 120308ER-D
+9° Fig.2
50-S42G 7 2 49 42 170 70 51 -2° SB-4070TRG DT-15 NEMT 16T308ER-D
Long Head MEZ 16-S16-140HG 4 2 16 16 140 51 16 -5° SB-2040TRG DTM-6 NDMT 080208ER-D
20-S20-150HG 4 2 20 20 150 53 21 -4° SB-2555TRG DT-8 NDMT 10T208ER-D
25-S25-170HG +9° Fig.1
4 2 25 25 170 70 25 -5° SB-3070TRG DT-10 NEMT 120308ER-D
32-S32-180HG 4 2 32 32 180 80 33 -2° SB-4070TRG DT-15 NEMT 16T308ER-D
MEZ 16-S16-190G 4 2 16 16 190 61 16 -5° SB-2040TRG DTM-6 NDMT 080208ER-D
Long Shank 20-S20-200G 4 2 20 20 200 63 21 -4° SB-2555TRG DT-8 NDMT 10T208ER-D
25-S25-220G +9° Fig.1
4 2 25 25 220 80 25 -5° SB-3070TRG DT-10 NEMT 120308ER-D
32-S32-230G 4 2 32 32 230 90 33 -2° SB-4070TRG DT-15 NEMT 16T308ER-D
40-S32-240G 7 2 39 32 240 55 39 -3° SB-3070TRG DT-10 NEMT 120308ER-D
50-S42-250G +9° Fig.2
7 2 49 42 250 70 51 -2° SB-4070TRG DT-15 NEMT 16T308ER-D
Recommended Cutting Conditions • Drilling conditions should be calculated as one flute
line.Step feed (0.5-0.1mm) is recommended.
Workpiece fz (ipt) Recommended Insert Grade (Vc: sfm)
Material • Coolant is recommended when drilling stainless
Drilling Shouldering Cermet MEGACOAT Carbide steel / cast iron.
Slotting
TN100M PR1225 PR1210 KW10 • Down-Cut milling is recommended for the
Carbon Steel 0.002~0.008 0.002~0.008 - - improvement of tool life and surface finish.
390~660 390~820 - - • Compressed air is recommended.
Alloy Steel 0.002~0.008 0.002~0.008 - -
330~590 330~720
Mold Steel 0.002~0.005 0.002~0.006 - -
Stainless Steel 0.002~0.005 0.002~0.006 330~590 260~590 330~720 260~490 (Shown from upside) (Shown from upside)
- Up-cut Down-cut
Cast Iron 0.002~0.008 0.002~0.008 330~980
390~660 390~720
Non-ferrous Metals 0.002~0.008 0.002~0.008
- -
- -
: 1st Recommendation : 2nd Recommendation Poor galling Excellent surface finish,
surface, wear stable and long tool
and chattering life, anti chattering
How to Use the Silver Drill Mill MEZ-G Effectively
Drilling Ramping · Helical Milling End Milling
• Step feeding is recommended for • Ramping angle is recommended • Tough edge insert is
good chip control. to be under 6°. recommended for high load
(Depth approx. 1mm) Under
• Plunge depth per revolution when D/2 end milling.
• Drill depth should be under 0.5D. helical milling should be under
(D:Drilling Dia.) 1/2D. Under 6° (High feed rate,large ap)
Use compressed air when during
machining. • Use compressed air when during Use a low cutting force N(D/E)MT...ER-DH N(D/E)MT...ER-DH
machining. (Tough Edge type) (Tough Edge type)
insert to prevent chattering.
G6 kyocera@kyocera-tools.ru U.S. Stock Standard :
www.kyocera-tools.ru World Express (Shipping: 7-10 Business Days) :