Kyocera - Каталог фрезерование 2017 ENG
для заказа - kyocera@kyocera-tools.ru
MECX
Recommended Cutting Conditions Recommended Insert Grade Vc (sfm)
Feed Rate fz (ipt)
MEGACOAT NANO MEGACOAT PVD Coated CVD Coated
PR1535 Carbide Carbide
Workpiece CA6535
Material JS Chipbreaker JT Chipbreaker
PR1225 PR1210 PR830
Carbon Steel 0.0016~0.0031~0.0039 0.0024~0.0039~0.0047 - -
390~590~820 390~590~820 390~490~590
Alloy Steel 0.0016~0.0024~0.0031 0.0024~0.0031~0.0039 - -
330~520~720 330~520~720 330~460~590
Mold Steel 0.0016~0.0024~0.0031 0.0024~0.0031~0.0039 - -
260~460~590 260~460~590 260~390~490
Austenitic Stainless Steel 0.0012~0.0016~0.0020 0.0020~0.0024~0.0028 - - -
330~520~660 330~520~660
Martensitic Stainless Steel 0.0012~0.0016~0.0020 0.0020~0.0024~0.0039 - - -
490~660~820 590~790~980
Precipitation Hardened 0.0012~0.0016~0.0020 0.0020~0.0024~0.0039 - - - -
Stainless Steel 300~390~490 -
90 LEADE Gray Cast Iron 0.0016~0.0031~0.0039 0.0031~0.0039~0.0059 - - -
390~590~820
Nodular Cast Iron 0.0016~0.0024~0.0031 0.0031~0.0039~0.0047 - - - -
330~490~660
Ni-base Heat Resistant Alloy 0.0012~0.0016~0.0020 0.0020~0.0024~0.0028 - - -
70~100~160 70~100~160
Titanium Alloys 0.0016~0.0024~0.0031 0.0031~0.0039~0.0047 - - -
130~200~260 100~160~230
:1st Recommendation
Bold numbers in the graph indicate the most recommended value of feed (fz) Adjust cutting speed and feed rate according to the actual machining conditions : 2nd Recommendation
Machining with coolant is recommended for Ni-base heat resistant alloy and titanium alloys
Ramping / Helical Milling
Ramping / Helical Milling
Ramping angle should be under °. Cutting Dia. Applicable Inserts Max. Ramping Angle (°)
BDMT 0703
For plunge depth per revolution when helical milling, 0.375”, 8mm Not Recommended
see the cutting performance data of each tool. Use compressed air during machining. 10mm 1.5°
0.500”
2°
12mm, 14mm
0.625”, 16mm 3°
17mm, 18mm 1.5°
0.750”, 20mm 2°
1.8°
21mm 1.3°
1.000”, 25mm 1.2°
0.8°
26mm 0.5°
1.250”, 32mm
33mm
Minimum Cutting Dia. for Helical Milling
MECX Cutting Dia. 0.375" 0.500" 0.625" 0.750" 8mm 10mm 12mm 14mm 16mm 17mm 18mm 20mm
BDMT0703 Min. Cutting Dia. 0.512" 0.748" 0.984" 1.260" Not recommended 14mm 18mm 22mm 26mm 28mm 30mm 34mm
Type Min. Cutting Dia. for Flat Bottom 0.630" 0.866" 1.142" 1.378" for helical milling. 17mm 21mm 25mm 29mm 31mm 33mm 37mm
MECX Cutting Dia. 1.000" 1.250" 21mm 25mm 26mm 32mm 33mm
BDMT0703 Min. Cutting Dia. 1.732" 2.244" 36mm 44mm 46mm 58mm 60mm
Type Min. Cutting Dia. for Flat Bottom 1.890" 2.362" 39mm 47mm 49mm 61mm 63mm
E26 kyocera@kyocera-tools.ru
www.kyocera-tools.ru