Kyocera - Инструмент для обработки мелких деталей 2016 ENG
для заказа - kyocera@kyocera-tools.ru
INSERT IDENTIFICATION SYSTEM
Symbol Hole Hole Shape Chipbreaker Insert
A NoGRADES
A
M With Hole One Side
Symbol Insert Tolerance G Two Sides
Symbol Corner Height Thickness I.C. Size
B T TriangleINSERTS (Class) ANSI ISO ANSI ISO ANSI ISO W With Hole and No
C 80 Rhombic (±inch) (±mm) (±inch) (±mm) (±inch) (±mm) One Countersink
40~60
T Yes One Side One Side
D 55 Rhombic Symbol Relief Angle E 0.0010 0.025
G 0.0010 0.025 0.0005 0.130 0.0010 0.025
J 70 Rhombic With Hole and
CBN & PCD V 35 Rhombic B 5 K 0.0005 0.013 0.0010 0.025 U One Countersink Two Sides
0.130 40~60
C W 80 Trigon 0.002~0.006 0.05~0.15 Two Sides
C 7 M 0.003~0.007 0.080~0.180 0.0005
Shown angle stands for N 0 Insert's periphery is as fired. B With Hole and No
acute angle for rhombic P 11 Tolerance difference depends on size and shape of insert One Countersink
and parallelogram inserts. 70~90
H One Side One Side
E Shape SymbolTURNING Relief Angle Symbol Tolerance Symbol Hole / Chipbreaker Symbol
F BORING ISO C C M T 06 02 02 GK
(metric)
G ANSI C C M T 2 15 05 GKGROOVING
(inch)
H Edge Length Symbol (ISO)CUT-OFF I.C. Size (ANSI) Thickness Symbol Corner-R(r) Symbol Manufacturer's
I.C. Size ISO ANSI ISO ANSI Option
(mm) I.C. Size Symbol Thickness Symbol Thickness Symbol Corner-R(r) Symbol Corner-R(r) Symbol
(inch) (mm) (inch) (mm) (inch)
Hand Symbol,
SOLID END MILLS THREADING 03 04 06 3.97 5/32 12 1.59 01 1/16 1 Sharp Corner 00 0.000 00 Chipbreaker,
J 04 05 08 08 4.76 3/16 15 1.98 T1 5/64 1.2 0.03 003 0.001 0.1 Symbol, Etc
05 06 09 03 5.56 7/32 18 2.38 02 3/32 1.5 0.05 005 0.002 0.13
06 07 11 11 04 6.35 1/4 2 2.78 T2 - - 0.1 01 0.004 0.2
08 09 13 05 7.94 5/16 25 3.18 03 1/8 2 0.2 02 0.008 0.5
09 11 16 16 06 9.525 3/8 3 3.97 T3 5/32 2.5 0.4 04 1/64 1
L 12 15 22 22 08 12.7 1/2 4 4.76 04 3/16 3 0.8 08 1/32 2
• Expressed as edge length for ISO. 1.2 12 3/64 3
• ANSI expresses the inscribed circle diameter in inches.
M MILLING
Thickness displayed as the distance between
bottom surface and highest point on cutting edge.
P SPARE PARTS
Positive Insert Identification System When a minus tolerance is specified for the corner-R(r)
TECHNICAL (e.g. of (8) Manufacturer's Option)
R CCGT21502M E R - U CCGT21502M F P - GF • If a minus tolerance is specified for the corner-R(r) as shown
in the Fig.1, using an insert with corner-R(r) = 0.008" may
Corner-R(r) for Corner-R(r) for result in larger radius than specified.
Minus Tolerance Minus Tolerance
T Honed EdgeINDEX Sharp edge • Use an insert the corner of which R(r) has a minus tolerance.
Insert Hand Chipbreakers Mirror-Finish Chipbreakers
Inserts
B2 Fig.1 Example of a specified corner-R in the drawing
kyocera@kyocera-tools.ru
www.kyocera-tools.ru