Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
[Cermet / Coated Carbide / Carbide]
35°Rhombic / Positive with Hole (mm) (mm)
Description A T d Description A T d
VB_1103_ 6.35 3.18 2.8 5 VC_0802_ 4.76 2.38 2.3 7 B
VB_1604_ 9.525 4.76 4.4 5 VC_1604_ 9.525 4.76 4.4 7
Positive
r P Free-Cutting Steel Insert
Classification of usage
M C
Carbon steel / Alloy steel D
K : Interruption / 1st Choice R
S
35° N Stainless Steel T
TS : Interruption / 2nd Choice V
W
H Gray Cast Iron
A : Light Interruption / 1st Choice
d
Nodular Cast Iron
TN6010 : Light Interruption / 2nd Choice
TN6020
Non-ferrous Metals
TN60 : Continuous / 1st Choice
PV7005
PV7010 Heat-Resistant Alloys
PV7025 : Continuous / 2nd Choice
CA5505
CA5515 Titanium Alloy
CA5525 (In case hardness is under 45HRC)
CA5535
CA6515 Hard materials
CA6525
CA4505Dim.CermetMEGACOATPVD CoatedMEGACOAT
CA4515(mm)CermetCarbide
PR930
PR1005
PR1025
PR1125
PR1225
PR1305
PR1310
PR1325
KW10
SW05
Ref. Page for
Toolholder
CVD Coated Carbide Carbide
Insert Description Applicable
Chipbreaker Range
Handed insert r
shows L-Hand (ap indicates radius)
VBGT 1103003 -Y 0.03 E28 Insert (Turning)
110301 -Y 0.1 E29
110302 -Y 0.2 E35
110304 -Y 0.4 F51
110308 -Y 0.8 F53
F55 (mm)
Finishing-Medium VBGT 160402 -Y 0.2 ap
160404 -Y 0.4 (Steel / Edge Length=11,16)
160408 -Y 0.8 E28 4
E29
VBGT 1103005M -Y < 0.05 F51 3
110301M -Y < 0.1 F53
110302M -Y < 0.2 F55 Y (Edge Length=16)
110304M -Y < 0.4
110308M -Y < 0.8 2
E28
E29 1
E35 Y 11
F51 F / FSF
F53
F55 0.1 0.2 0.3 0.4
f (mm rev)
VBGT 160402M -Y < 0.2 E28
160404M -Y < 0.4 E29
160408M -Y < 0.8 F51
F53
F55
Finishing VCMT 080202VF 0.2 E35 (mm) (Steel)
080204VF 0.4 F51 4
F53
VCMT 080202HQ 0.2 F55 3
080204HQ 0.4
E29 ap
VCMT 110304HQ 0.4 F51
Finishing-Medium F53 2 HQ
F55 VF
E35
F51 1
F53
VCMT 160404HQ 0.4 F55 0.1 0.2 0.3 0.4
160408HQ 0.8 f (mm rev)
VCGT 110301FN-Z 0.1
110302FN-Z 0.2
110304FN-Z 0.4
Medium / Sharp Edge
Non-ferrous Metals Non-ferrous Metals (mm) (Non-ferrous Metals)
4
VCGT 160404AH 0.4 3
AH
ap
2
Finishing-Medium / Sharp Edge E29
F51 1 A3
VCGT 160404 -A3 0.4 F53
VCGT 160408 -A3 0.8 F55 0.1 0.2 0.3 0.4
f (mm rev)
Finishing-Medium / Sharp Edge
VCGT 160412 1.2
Non-ferrous Material VCGT 220530 3.0 -
Medium-Roughing
Insert whose corner R(r) dimension expressed with less than sign (e.g.<0.05, <0.1, <0.2 etc.) indicate models with minus tolerance for corner R (r).
TN30 PV30 PV60 PV90 PV7020 Reference Page B74
CA4010 CA4115 CA4120 PR915 PR905
Inserts are sold in 10 piece boxes.
B73
: Std. Item R : Std. Item (R-hand Only) L : Std. Item (L-hand Only) : Check Availability
для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru