Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
Turnin8g0In°dexableInserts
80°Trigon / Negative with Hole Description A T (mm) Description A T (mm)
WN_06T3_ 9.525 3.96 d WN_0804_ 12.70 4.76 d
9.525 4.76
WN_0604_ 3.81 5.16
3.81
B 80 P Free-Cutting Steel
ONT Classification of usage
Negative r Carbon steel / Alloy steel
C T: Interruption / 1st Choice
D Insert M NQ P Stainless Steel
R S: Interruption / 2nd Choice
S Handed Insert S NT S Gray Cast Iron
T shows R-hand K
V A d P NT Q: Light Interruption / 1st Choice
W Nodular Cast Iron
P: Light Interruption / 2nd Choice
N T Non-ferrous Metals
S OP P NQT N: Continuous / 1st Choice
Heat-Resistant Alloys
O: Continuous / 2nd Choice
T S Q Titanium Alloy
Description (In case hardness is under 45HRC)
H Hard materials
Dim. Cermet MEGACOAT CVD PVD MEGACOAT Carbide Ref. Page for Applicable
(mm) Cermet Coated Carbide Coated Carbide Chipbreaker Range
Toolholder
r TN6010TN6020TN60PV7005PV7010PV7025CA5505CA5515CA5525CA5535CA6515CA6525CA4505CA4515PR930PR1005PR1025PR1125PR1225PR1305PR1310PR1325KW10 (ap indicates radius)
SW05
Stainless Steel / Heat-Resistant Alloys Heat-Resistant Alloys WNMG 080404MS 0.4 (mm) (Stainless Steel)
080408MS 0.8 5 TK
080412MS 1.2 4
3 MU
Medium-Roughing 0.4
0.8
Insert (Turning) Stainless Steel / WNMG 080404MU ap
080408MU 0.4
0.8 2
Medium-Roughing 0.4 1
0.8 MQ MS
Stainless Steel / Heat-Resistant Alloys WNGG 080404TK
080408TK 0.4 0.1 0.2 0.3 0.4 0.5
0.8 (mm/rev)
Medium-Roughing / Sharp edge 1.2
WNMG 080404TK 0.8 Heat-Resistant Alloys
080408TK 1.2 Titanium Alloys
Applicable Chipbreaker Range
Medium-Roughing WNMG 080404C 0.8
Roughing 080408C 1.2 See B7
080412C
Cast Iron 0.8 (mm) (Cast Iron)
1.2 10
D20 8 C (Standard)
F72 ap ap
6 GC
CastIron WNMG 080408ZS ZS
080412ZS
4
2
Roughing 0.2 0.4 0.6 0.8 1.0
f (mm/rev)
Cast Iron WNMG 080408GC (mm)
080412GC 5
4 (Non-ferrous Metals)
Roughing 3 AH
2
Cast Iron WNMA 080408 1
080412
Without Chipbreaker
Non-ferrous Metals WNGG 080404AH 0.4 0.1 0.2 0.3 0.4 0.5
080408AH 0.8
f (mm/rev)
Medium-Roughing / Sharp edge 0.2
0.4
0.8
Finishing WNGG 060402&-S (mm) (Steel)
4
060404&-S
060408&-S 3
D20
Surface Roughness Oriented F71 ap 2
1
(Without
S Indication)
Medium WNGG 060404& 0.4 0.1 0. 0.3 0.4 0.5
060408& 0.8
f (mm/rev)
TN30
CA4010
PV30 PV60 PV90 PV7020 Reference Page B41
CA4115 CA4120 PR915 PR905
Inserts are sold in 10 piece boxes.
B40 : Std. Item R : Std. Item (R-hand Only) L : Std. Item (L-hand Only) : Check Availability
для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru