Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
Turning Indexable Inserts (mm)
(mm) Description A T d
60°Triangle / Negative with Hole Description A T d TN_1603_ 9.525 3.18 3.81
60°Triangle / Negative without Hole
TN_1103_ 6.35 3.18 2.26 TN_1604_ 9.525 4.76 3.81
TN_1104_ 6.35 4.76 2.26 TN_2204_ 12.70 4.76 5.16
B P Free-cutting steel Classification of usage
Negative 60 Carbon steel / Alloy steel
C
D M Stainless Steel : Interruption / 1st Choice
R
S Gray Cast Iron : Interruption / 2nd Choice
T
V K Nodular Cast Iron : Light Interruption / 1st Choice
W
A N Non-ferrous Metals : Light Interruption / 2nd Choice
d
r Heat-resistant alloy : Continuous / 1st Choice
T TN6010S : Continuous / 2nd Choice
TN6020 Titanium Alloy
(In case hardness is under 45HRC)
TN60H Hard Materials
PV7005
PV7010Dim.MEGACOATPVD
PV7025(mm)CermetCoated Carbide
CA5505
CA5515
CA5525
CA5535
CA6515
CA6525
CA4505
CA4515
PR930
PR1005
PR1025
PR1125
PR1225
PR1305
PR1310
PR1325
KW10
SW05
Ref. Page for
Toolholder
Cermet CVD MEGACOAT Carbide
Coated Carbide
Applicable
Insert Description Chipbreaker Range
r (ap indicates radius)
Handed Insert
shows R-hand
Finishing TNGG 110402 -S 0.2 D14
110404 -S 0.4 F70
110408 -S 0.8
D14
TNGG 160401 -S 0.1 D15 (mm)
-S 0.2 F65 (Steel / Edge Length=11)
160402 -S 0.4 F70
-S 0.8 5
Insert (Turning) 160404
4
Surface Roughness Oriented 160408
3
Super Fine ap
2
Finishing TNEG 160402 -SSF 0.2 B
160404 -SSF 0.4
1S
0.1 0.2 0.3 0.4 0.5
f (mm/rev)
Sharp Edge / Precision
TNGG 110302 -B 0.2 D14
110304 -B 0.4
110308 -B 0.8
TNGG 160304 -B 0.4 - (mm)
(Steel / Edge Length=16)
0.2 D14
0.4 D15 5
0.8 F65
TNGG 160402 -B F70 4C
160404 -B 0.2 B(Y)
160408 -B 0.4
0.8 3
1.2
Finishing / Medium-Roughing / Roughing TNGG 160402 -C 1.6 ap ap 2S
160404 -C 1
160408 -C
160412 -C 25R
160416 -C
0.1 0.2 0.3 0.4 0.5
f (mm/rev)
TNGG 220404 -C 0.4 D14
220408 -C 0.8
D14 (mm)
TNGG 220412 -D 1.2 F70 (Steel / Edge Length=22)
TNGG 110402 0.2 10
110404 0.4 8
110408 0.8 6
TNMG 160404 -C 0.4 4 D
160408 -C 0.8 C
160412 -C 1.2
2
-B Finishing-Medium D14 0.2 0.4 0.6 0.8 1.0
-C Medium-Roughing D15 f (mm/rev)
-D Roughing F65
F70
Medium-Roughing Medium-Roughing Low Cutting Force TNGG 160404 -25R 0.4
160408 -25R 0.8
TNGG 160404FP-TK 0.4 E19
160408FP-TK 0.8
D14
Sharp Edge / Polished D15 See B44
F65
F70
TN30 PV30 PV60 PV90 PV7020 Reference Page B35
CA4010 CA4115 CA4120 PR915 PR905
B34 Inserts are sold in 10 piece boxes.
: Std. Item R : Std. Item (R-hand Only) L : Std. Item (L-hand Only) : Check Availability
для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru