Kyocera - Основной каталог 2011-2012 ENG
High efficiency chip evacuation,для заказа - kyocera@kyocera-tools.ru
Roughing, Notched surface
4RFSM, 6RFSM Workpiece Materials No. of Flutes: 4, 6
1st choice
I
Shank Dia.
46
4RFSM Shouldering Slotting 6RFSM Shouldering Slotting
(Unit : mm) (Unit : mm)
Outside Length Shank Overall No. of Outside Length Shank Overall No. of
Dia. Mill Dia. of cut diameter length Flutes Dia. Mill Dia. of cut diameter length Flutes
Description Std. tolerance Description Std. tolerance
Dc Dc
4RFSM060-130-06 Ds L Z 6RFSM160-320-16 Ds L Z
4RFSM080-160-08 6RFSM200-380-20
4RFSM100-220-10 6 -0.030 13 6 57 4 6RFSM250-450-25 16 -0.050 32 16 92 6
4RFSM120-260-12 -0.105 -0.160
4RFSM160-320-16
4RFSM200-380-20 8 -0.040 16 8 63 4 20 -0.065 38 20 104 6
-0.130 -0.195
10 -0.040 22 10 72 4 25 -0.065 45 25 121 6
-0.130 -0.195
12 -0.050 26 12 83 4
-0.160
16 -0.050 32 16 92 4
-0.160
20 -0.065 38 20 104 4 Recommended Cutting Conditions L44
-0.195
RFS type is applicable for hardened metals and titanium alloys due to strong cutting edge with notched surface and L
45 degrees helix angle.
High efciency chip evacuation,
Roughing, Notched surface, Radius
3RFRS, 4RFRS Workpiece Materials No. of Flutes: 3, 4 Solid End Mill
1st choice
Radius 0.05 I
R
mm Shank Dia.
R
34
3RFRS (Radius) Shouldering Slotting 4RFRS (Radius) Shouldering Slotting
(Unit : mm) (Unit : mm)
Outside Mill Dia. Length Shank Overall Spec of Under Neck No. of Outside Mill Dia. Length Shank Overall Spec of Under Neck No. of
tolerance tolerance
Description Std. Dia. of cut diameter length Corners Length Flutes Description Std. Dia. of cut diameter length Corners Length Flutes
Dc Ds L Z Dc Ds L Z
3RFRS040-040-06-R075 4 -0.030 4 6 75 R 0.75 27.5 3 4RFRS060-060-10-R075 6 -0.030 6 10 100 R 0.75 52.5 4
3RFRS050-050-06-R075 -0.105 -0.105
5 -0.030 5 6 75 R 0.75 17 3 4RFRS080-080-10-R075 8 -0.040 8 10 100 R 0.75 31.5 4
-0.105 -0.130
4RFRS100-100-12-R075 10 -0.040 10 12 125 R 0.75 33.5 4
-0.130
4RFRS120-120-16-R100 12 -0.050 12 16 125 R 1.0 58.5 4
-0.160
Due to the strong cutting edge with large at surface, it is suitable for handened metals and titanium alloys.
It can provide good surface roughness of 2.5 to 4.9 mRa. Recommended Cutting Conditions L45
: Check Availability
для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru L23