Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
[Cermet / Coated Carbide / Carbide]
(mm)
60°Triangle / Negative with Hole Description A T (mm) Description A T d
TN_1103_ 6.35 3.18 TN_1603_ 9.525 3.18 3.81
TN_1104_ 6.35 4.76 d TN_1604_ 9.525 4.76 3.81
2.26 TN_2204_ 12.70 4.76 5.16
2.26
60 P Free-cutting steel Classification of usage B
r Carbon Steel / Alloy Steel : Interruption / 1st Choice
M Stainless Steel : Interruption / 2nd Choice Negative
Insert Gray Cast Iron : Light Interruption / 1st Choice C
K Nodular Cast Iron : Light Interruption / 2nd Choice D
: Continuous / 1st Choice
A N Non-ferrous Metals : Continuous / 2nd Choice
d Heat-resistant alloy
T S Titanium Alloy (In case hardness is under 45HRC)
TN6010Description
TN6020H Hard Materials
TN60Dim.CermetCVD PVD
PV7005(mm)
PV7010Coated Carbide Coated Carbide Applicable R
PV7025 Chipbreaker Range S
CA5505r
CA5515 (ap indicates radius)
CA5525
Medium-Roughing / High Feed Medium-Roughing / High Feed Medium-Roughing / High Feed CA5535TNMG 160408PT0.8 (mm) T
CA6515160412PT1.2 (Steel / Edge Length=16) V
CA6525 W
CA4505 5
CA4515 Standard
PR930
PR1005 4 PS(HS) GT
PR1025
PR1125 3
PR1225
PR1305TNMG 160408GT0.8 D14 2 PT Insert (Turning)
PR1310160412GT1.2 D15 GS
PR1325 F65
KW10 F70 1
SW05
D14 0.1 0.2 0.3 0.4 0.5
Ref. Page for
Toolholder D14 f (mm/rev)
D15
ap ap ap ap apTNMG 160408HT0.8F65(mm)
160412HT 1.2 F70 (Steel / Edge Length=22)
TNMG 160404 0.4 D14 10
160408 0.8
160412 1.2 D14 8 Standard
160416 1.6 D15 6 PS(HS)
160420 2.0 F65
Roughing F70 4
TNMG 220404 0.4
220408 0.8 D14 2
220412 1.2
CQ
TNMG 160408PH 0.8
160412PH 1.2 0.2 0.4 0.6 0.8 1.0
TNMG 220408PH 0.8 f (mm/rev)
220412PH 1.2
Low Carbon Steel Low Carbon Steel Low Carbon Steel Low Carbon Steel Single Sided / Roughing / High Feed Medium-Roughing 220416PH 1.6 (mm) (Steel)
TNMM 160408PX 0.8 10 PH
160412PX 1.2
8 PH (Edge Length=22)
TNMM 220408PX 0.8 (Edge Length=16)
220412PX 1.2
220416PX 1.6 6
4
2
0.2 0.4 0.6 0.8 1.0
f (mm/rev)
TNMG 160404XP 0.4 (mm) (Steel)
160408XP 0.8 10
8 PX
Finishing 6 (Edge Length=22)
4
TNMG 160404XP-T 0.4 2 PX
160408XP-T 0.8 (Edge Length=16)
Finishing / Tough Edge Type D14 0.2 0.4 0.6 0.8 1.0
D15
F65 f (mm/rev)
F70
(mm) (Low Carbon Steel)
5
TNMG 160404XQ 0.4
160408XQ 0.8 4
3
Medium
2 XP XS
1 XP-T XQ
TNMG 160408XS 0.8
Medium 0.1 0.2 0.3 0.4 0.5
f (mm/rev)
Inserts are sold in 10 piece boxes. B31
: Std. Item R : Std. Item (R-hand Only) L : Std. Item (L-hand Only) : Check Availability
для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru