Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
Cermet / Coated Carbide / Carbide
90°Square / Negative with Hole Description A T mm Description A T mm
SN_0903_ 9.525 3.18 d SN_1506_ 15.875 6.35 d
SN_1204_ 12.70 4.76 SN_1906_ 19.05 6.35
3.81 6.35
5.16 7.94
A Pd Free-Cutting Steel B
M Classification of usage
K Negative
N Carbon steel / Alloy steel C
: Interruption / 1st Choice D
TS R
Stainless Steel S
H : Interruption / 2nd Choice T
V
Gray Cast Iron W
: Light Interruption / 1st Choice
Nodular Cast Iron
: Light Interruption / 2nd Choice
Non-ferrous Metals
: Continuous / 1st Choice
Heat-Resistant Alloys
: Continuous / 2nd Choice
Titanium Alloy
(In case hardness is under 45HRC)
Hard materials
Dim. Cermet MEGACOAT CVD Coated Carbide PVD Coated MEGACOAT Carbide
(mm) Cermet Carbide
TN6010 Applicable
Insert Description TN6020 Chipbreaker Range
Handed Insert r TN60 (ap indicates radius)
shows R-hand PV7005
PV7010
PV7025
CA5505
CA5515
CA5525
CA5535
CA6515
CA6525
CA4505
CA4515
PR930
PR1005
PR1025
PR1125
PR1225
PR1305
PR1310
PR1325
KW10
SW05
Ref. Page for
Toolholder
Medium-Roughing Stainless Steel / Heat-Resistant Alloys Stainless Steel / Heat-Resistant Alloys Stainless Steel / Heat-Resistant Alloys Low Carbon Steel Low Carbon Steel Low Carbon Steel Single Sided / Roughing / High Feed SNMM 120408PX 0.8 D12 (mm) Steel
120412PX 1.2 D13 12
120416PX 1.6 10 PX 19
- 8 PX 15
SNMM 150612PX 1.2
150616PX 1.6 ap 6
SNMM 190612PX 1.2 4 Insert (Turning)
190616PX 1.6
190624PX 2.4 2 PX 12
0.2 0.4 0.6 0.8 1.0
f (mm/rev)
SNMG 120408XP 0.8 (mm) Low Carbon Steel
5
Finishing 4
ap 3
SNMG 120408XQ 0.8 2 XQ XS
1
XP
Medium 0.1 0.2 0.3 0.4 0.5
f (mm/rev)
SNMG 120408XS 0.8 D12
D13
0.4
Roughing 0.8
SNMG 120404MQ 0.4 (mm) Stainless Steel
120408MQ 0.8 5 19
1.2
Finishing-Medium SNMG 120404MS 1.6 ap 4
Medium-Roughing 120408MS MS
120412MS 1.2
120416MS 1.6 3
2
1
MQ
0.1 0.2 0.3 0.4 0.5
f (mm/rev)
Heat-Resistant Alloys
SNMG 190612MU - Titanium Alloys
190616MU Applicable Chipbreaker Range
Medium-Roughing See B7
SNMG 120408 -ST 0.8 See B6
Low Cutting Force
TN30 PV30 PV60 PV90 PV7020 Reference Page B29
CA4010 CA4115 CA4120 PR915 PR905
B27Inserts are sold in 10 piece boxes.
: Std. Item R : Std. Item (R-hand Only) L : Std. Item (L-hand Only) : Check Availability
для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru