Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
MagicDrill® DRX
DRX Recommended Cutting Conditions (Coolant)
Recommended Insert Grade (Cutting Speed : m/min) Toolholder Type
MEGACOAT Carbide Cutting
Workpiece PR1230 PR1225 PR1210 GW15 Dia.
Material Dc 2D~3D 4D 5D
GM SM GM SM (mm) GH SM f (mm/rev) GM GH SM
GH GM GM GH SM
12~15 0.06~0.10 0.06~0.10 0.04~0.10 0.05~0.08 0.05~0.08 0.04~0.08 0.04~0.07 0.04~0.07 0.04~0.08
Low Carbon 15.5~18 0.06~0.12 0.06~0.12 0.06~0.12 0.05~0.10 0.05~0.10 0.05~0.10 0.05~0.08 0.05~0.08 0.04~0.09
18.5~26 0.08~0.14 0.08~0.14 0.06~0.14 0.06~0.12 0.08~0.12 0.05~0.12 0.06~0.10 0.06~0.10 0.04~0.10
Steel 120-240 120-240
26.5~60 0.08~0.14 0.08~0.14 0.06~0.14 0.06~0.12 0.08~0.12 0.05~0.12 0.06~0.10 0.06~0.10 0.04~0.10
12~15 0.04~0.14 0.04~0.14 0.04~0.10 0.04~0.10 0.04~0.10 0.04~0.08 0.04~0.08 0.04~0.08 0.04~0.07
Carbon Steel 15.5~18 0.06~0.16 0.06~0.16 0.06~0.12 0.05~0.12 0.05~0.12 0.05~0.10 0.05~0.10 0.05~0.10 0.05~0.08
18.5~26 0.08~0.20 0.08~0.20 0.06~0.14 0.07~0.16 0.07~0.16 0.05~0.12 0.06~0.12 0.06~0.12 0.05~0.10
100-180 100-180
26.5~60 0.08~0.20 0.08~0.20 0.06~0.14 0.07~0.16 0.07~0.16 0.05~0.12 0.06~0.12 0.06~0.12 0.05~0.10
12~15 0.04~0.14 0.04~0.14 0.04~0.10 0.04~0.10 0.04~0.10 0.04~0.08 0.04~0.08 0.04~0.08 0.04~0.07
Alloy steel 15.5~18 0.06~0.16 0.06~0.16 0.06~0.12 0.05~0.12 0.05~0.12 0.05~0.10 0.05~0.10 0.05~0.10 0.05~0.08
18.5~26 0.08~0.20 0.08~0.20 0.06~0.14 0.07~0.16 0.07~0.16 0.05~0.12 0.06~0.12 0.06~0.12 0.05~0.10
100-160 100-160
26.5~60 0.08~0.20 0.08~0.20 0.06~0.14 0.07~0.16 0.07~0.16 0.05~0.12 0.06~0.12 0.06~0.12 0.05~0.10
12~15 0.04~0.08 0.04~0.08 0.04~0.08 0.04~0.07 0.04~0.07 0.04~0.07 0.04~0.06 0.04~0.06 0.04~0.06
Die Steel 80-150 80-150 15.5~18 0.06~0.12 0.06~0.12 0.06~0.10 0.05~0.10 0.05~0.10 0.05~0.08 0.04~0.08 0.04~0.08 0.04~0.07
18.5~26 0.08~0.15 0.08~0.15 0.06~0.12 0.06~0.12 0.06~0.12 0.06~0.10 0.05~0.10 0.05~0.10 0.05~0.08
26.5~60 0.08~0.15 0.08~0.15 0.06~0.12 0.06~0.12 0.06~0.12 0.06~0.10 0.05~0.10 0.05~0.10 0.05~0.08
12~15 0.06~0.10 0.06~0.10 0.04~0.10 0.05~0.08 0.05~0.08 0.04~0.08 0.04~0.07 0.04~0.08 0.04~0.08
Stainless 70-140 70-140 15.5~18 0.06~0.10 0.06~0.10 0.06~0.12 0.05~0.08 0.05~0.08 0.05~0.11 0.04~0.07 0.04~0.07 0.04~0.10
Steel 18.5~26 0.08~0.12 0.08~0.12 0.06~0.14 0.07~0.10 0.07~0.10 0.06~0.12 0.07~0.10 0.07~0.10 0.06~0.12
26.5~60 0.08~0.12 0.08~0.12 0.06~0.14 0.07~0.10 0.07~0.10 0.06~0.12 0.07~0.10 0.07~0.10 0.06~0.12
12~15 0.08~0.14 ~ ~ 0.06~0.12 ~ ~ 0.04~0.10 ~ ~
Gray Cast 100-150 15.5~18 0.08~0.18 ~ ~ 0.08~0.16 ~ ~ 0.06~0.12 ~ ~
18.5~26 0.08~0.20 ~ ~ 0.08~0.18 ~ ~ 0.06~0.14 ~ ~
K Iron
26.5~60 0.08~0.20 ~ ~ 0.08~0.18 ~ ~ 0.06~0.14 ~ ~
12~15 0.08~0.12 ~ ~ 0.06~0.10 ~ ~ 0.04~0.08 ~ ~
Nodular Cast 80-120 15.5~18 0.08~0.16 ~ ~ 0.08~0.14 ~ ~ 0.06~0.10 ~ ~
Iron 18.5~26 0.08~0.18 ~ ~ 0.08~0.16 ~ ~ 0.06~0.12 ~ ~
Drilling 26.5~60 0.08~0.18 ~ ~ 0.08~0.16 ~ ~ 0.06~0.12 ~ ~
12~15 ~ ~ 0.06~0.12 ~ ~ 0.05~0.10 ~ ~ 0.04~0.08
Non-ferrous 15.5~18 ~ ~ 0.08~0.14 ~ ~ 0.06~0.12 ~ ~ 0.05~0.10
Metals 200-600 18.5~26 ~ ~ 0.08~0.16 ~ ~ 0.06~0.14 ~ ~ 0.05~0.12
26.5~60 ~ ~ 0.08~0.20 ~ ~ 0.08~0.16 ~ ~ 0.07~0.14
12~15 ~ ~ 0.05~0.08 ~ ~ 0.04~0.07 ~ ~ 0.04~0.06
Titanium 40-70 15.5~18 ~ ~ 0.05~0.08 ~ ~ 0.04~0.07 ~ ~ 0.04~0.06
Alloys 18.5~26 ~ ~ 0.06~0.10 ~ ~ 0.06~0.08 ~ ~ 0.05~0.07
26.5~60 ~ ~ 0.06~0.10 ~ ~ 0.06~0.08 ~ ~ 0.05~0.07
• Apply a sufcent amount of coolant. 1st. Recommendation 2nd. Recommendation
Cutting Conditions by Application
Applications Flat Surface Slanted Half Cylindrical Hole Concave Pre-drilled Stacked Plates
Surface Expansion Surface Surface
Workpiece Shape
Cutting Speed (m/min) 120 120 120 120 120 120 Not Available
0.05 Concave part 0.05 Not Available
DRX Yes Yes Not Available
0.05
type Feed Rate (mm/rev) 0.1 0.05 0.05 Continuous part 0.1 5D
Not Recommended
Coolant (internal) Yes Yes Yes Yes
* Cutting width (Torus-shaped part) when machining pre-drilled surface
Drill type 2D~3D 4D
Cutting width (Torus-shaped part) 1/10XD or less less than corner radius
Max. Depth for Machining with Outer Coolant
When machining with outer coolant, Max. depth should be 1.5 times of the cutting diameter.
K34 для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru