Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
Turning Indexable Inserts
80°Rhombic / Negative with Hole Description A T (mm) Description A T (mm)
CN_0903_ 9.525 3.18 CN_1204_ 12.70 4.76
CN_0904_ 9.525 4.76 d CN_1606_ 15.875 6.35 d
3.81 CN_1906_ 19.05 6.35 5.16
3.81 6.35
7.94
B
P Free-cutting steel Classification of usage
Negative
$ Ar Carbon Steel / Alloy Steel : Interruption / 1st Choice
% d
3 M Stainless Steel : Interruption / 2nd Choice
4
5 K Gray Cast Iron : Light Interruption / 1st Choice
7
8 Nodular Cast Iron : Light Interruption / 2nd Choice
N Non-ferrous Metals
Heat-resistant alloy : Continuous / 1st Choice
80 T S : Continuous / 2nd Choice
Description Titanium Alloy
(In case hardness is under 45HRC)
H Hard Materials
Dim. Cermet MEGACOAT CVD PVD MEGACOAT Carbide
(mm) Cermet Coated Carbide Coated Carbide
TN6010 Applicable
Insert TN6020 Chipbreaker Range
r TN60 (ap indicates radius)
PV7005
PV7010
PV7025
CA5505
CA5515
CA5525
CA5535
CA6515
CA6525
CA4505
CA4515
PR930
PR1005
PR1025
PR1125
PR1225
PR1305
PR1310
PR1325
KW10
SW05
Ref. Page for
Toolholder
Insert (Turning) CNMG 120404 0.4 D8 ap (mm)
Roughing 120408 0.8 F64 (Steel / Edge Length=19)
120412 1.2 F68
120416 1.6 10
D8 Standard
CNMG 160608 0.8
160612 1.2 8
160616 1.6
6 HX
CNMG 190608 0.8
190612 1.2 4
190616 1.6 HS
190624 2.4
2
CNMG 120408PH 0.8
120412PH 1.2 0.2 0.4 0.6 0.8 1.0
120416PH 1.6
f (mm/rev)
CNMG 160608PH 0.8
Roughing 160612PH 1.2 D8 ap ap(mm)
160616PH 1.6 F64 (Steel / Edge Length=12,16,19)
F68
CNMG 190608PH 0.8 12
190612PH 1.2 D8 PH(19)
190616PH 1.6
190624PH 2.4 10
PH(16)
CNMM 120408PX 0.8
120412PX 1.2 8
120416PX 1.6
6
CNMM 160608PX 0.8
160612PX 1.2 4
160616PX 1.6 PH(12)
CNMM 190608PX 0.8 2
190612PX 1.2
190616PX 1.6 0.2 0.4 0.6 0.8 1.0
190624PX 2.4
f (mm/rev)
Single Sided / Roughing / High Feed D8 (mm) (Steel)
F64 12
F68 10 PH(19)
8 PH(16)
D8
6
4
2 PH(12)
0.2 0.4 0.6 0.8 1.0
f (mm/rev)
Low Carbon Steel Low Carbon Steel Low Carbon Steel Low Carbon Steel CNMG 120404XP 0.4
120408XP 0.8
Finishing
CNMG 120404XP-T 0.4 (mm) (Low Carbon Steel)
120408XP-T 0.8 5
Finishing / Tough Edge Type D8 4
F64
F68 ap 3
CNMG 120404XQ 0.4 2 XS
120408XQ 0.8 XP XQ
1 XP-T
Medium 0.1 0.2 0.3 0.4 0.5
f (mm/rev)
CNMG 120408XS 0.8
Roughing
TN30 PV30 PV60 PV90 PV7020 Reference Page B19 Inserts are sold in 10 piece boxes.
CA4010 CA4115 CA4120 PR915 PR905
B16
: Std. Item R : Std. Item (R-hand Only) L : Std. Item (L-hand Only) : Check Availability
для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru