Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
Face Grooving Toolholders (Separate type)
KGDF
Toolholder Dimensions
Angle Unit Description Std. Blade Description Dimension (mm) Width Face Grooving Dia.
Width Toolholder G73 H1=h H2 H3 B L1 L2 F1 (mm) D(mm)
Max. depth of cut Description
T W MIN. MAX.
R L G28
(mm) (mm)
KGDF 2020X25-6BS KGDF -25-6B-C 25 35
KGDL/R2020-C -35-6B-C
2020X35-6BS -50-6B-C 35 50
KGDF -75-6B-C
2020X50-6BS KGDL/R2525-C -115-6B-C 50 75
-180-6B-C
15 2020X75-6BS -235-6B-C 120 38 15 75 115
-25-6C-C
2020X115-6BS -35-6C-C 115 180
-50-6C-C
2020X180-6BS -75-6C-C 180 235
-115-6C-C 235
2020X235-6BS -180-6C-C 20 12 11.6 20 125 43 24.2 20
-235-6C-C
20 2020X25-6CS -25-6B-C 25 35
-35-6B-C
2020X35-6CS -50-6B-C 35 50
-75-6B-C
2020X50-6CS -115-6B-C 50 75
-180-6B-C
25 2020X75-6CS -235-6B-C 130 48 25 75 115
2020X115-6CS -25-6C-C
G -35-6C-C 115 180
-50-6C-C
2020X180-6CS -75-6D-C 180 235
-115-6D-C 235
0° 6 2020X235-6CS -180-6D-C 6 25 35
KGDF 2525X25-6BS -235-6D-C
2525X35-6BS 35 50
2525X50-6BS 50 75
Grooving 15 2525X75-6BS 145 38 15 75 115
2525X115-6BS 115 180
2525X180-6BS 180 235
235
2525X235-6BS 25 7 11.6 25 150 43 29.2 20
20 2525X25-6CS 25 35
25 2525X35-6CS 155 48 25 35 50
2525X50-6CS
50 75
2525X75-6DS 75 115
32 2525X115-6DS 162 55 32 115 180
2525X180-6DS
180 235
235
2525X235-6DS
Spare Parts
Clamp Bolt Spare Parts Wrench
(for Insert Clamp)
Unit Fixing bolt
Description (for blade)
KGDF .....S BH6X10TR SB-60120TR LTW-25 * Note that the parts are included in the toolholder
when purchasing the toolholder and blade
separately.
Face Grooving Dia. D Minimum traversing diameter of small groove Traversing towards the Center causes the toolholder to interfere with the groove wall depending on the initial cut's diameter.
Face grooving diameter (D) is the suitable value for the initial D 25 26 27 28
grooving on the unprocessed workpiece (see Fig.1). Then, d Over
you can widen it up to the center towards the inside (excluding
the models listed in the right table), and towards the outside d Description
according to machine limits.
KGDF 2020X25-3AS 4 2 0 0
2525X25-3AS
(No remaining Boss)
D KGDF 2020X25-4AS 6 3 0
Interference
2525X25-4AS
KGDF 2020X25-5AS
2525X25-5AS 7 4 1
Remaining Boss Dia.d
KGDF 2020X25-6AS
2525X25-6AS 9 4 1
Example)
If a groove of external diameter 25 is created using
KGDFR2020X25-3AS and traversing is made toward the inside, a
4 portion will be left in middle due to interference of toolholder.
Fig.1
: Std. Item : Check Availability
G72 для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru