Kyocera - Основной каталог 2011-2012 ENG

                                                                   для заказа - kyocera@kyocera-tools.ru                                                                                          Grooving / Plunge&Turn

Internal Grooving Toolholder / Internal Undercutting Toolholder

  KIGM-8 (8mm-Width Insert / Large Internal Diameter Deep Grooving)

                                                                                                          A L2
                                                                                                                                                                                                                        D
                                             AT
                                                                                                                                                                   45
                                                                                            F                                                                W                                             H
                                                                                                                        F                                                  W L1

                                                        Right-hand shown                                                          T
                                                                                                                                                            D
KIGMU-8 (8mm-Width Insert / Large Internal Diameter Undercut Grooving)

             Ad

                                                                                                                                                                                                                                                                                                  G

                                                                                                                                                             L2                H
                                                                                                                                                                           L1

                                                        Right-hand shown

Toolholder Dimensions                                                                                                                                                                                                                                                                             Grooving

                                                       Std.                     Min.        Dimension (mm)                                                                     Width              Spare Parts
                                                                              Cutting Dia.                                                                                     (mm)
                                                                                                                                                                                                  Screw                             Wrench

       Description

                                                       R L A D H L1 L2 F T d                                                                                                 MIN. MAX.

KIGM         6540B-8                                                          65 40 36 300 41 41 20 -                                                                          8.0 8.0 HH6X20 LW-5
KIGMU        6540B-8                                                          65 40 36 300 83 26 - 2.2                                                                         8.0 8.0 HH6X20 LW-5

Dimension T shows available grooving depth.
Dimension d shows the distance from the Internal face of the workpiece.

Applicable Inserts (mm)                                                                                                                                      P Carbon Steel / Alloy Steel                                           Classification of usage
                                                                                                                                                             M Stainless Steel
Description                                  LH                                                                                                              K Cast Iron                                                               : Continuous-Light Interruption / 1st Choice
                                                                                                                                                             N Non-ferrous Metals                                                      : Continuous-Light Interruption / 2nd Choice
GMM8030-080MW                                                                                                                                                S Titanium Alloy                                                          : Continuous / 1st Choice
                                                                                                                                                                                                                                       : Continuous / 2nd Choice
GMG8030-050MG 30                                          5.5                                                                                                       Hard materials (under 40HRC)
                                                                                                                                                                                                                                     Applicable
GMGA8030-400R                                                                                                                                                H                                                                       Toolholder

                                                                                                                                                                    Hard materials (over 40HRC)

                                                                                                                                                                                                  Cermet
                                                                                                                                                                                                      CVD Coated

                                                                                                                                                                                                         Carbide

                                                                                                                                                                                                                      Carbide
                                                                                                                                                                           Dimension (mm)                                    PVD                                                   Ref. Page for
                                                                                                                                                                            W r M                                         Coated                                                     Toolholder
                                                                                                                                                                                                                           Carbide

               Insert                                                                       Description                                                      (Previous                           TN90
                                                                                                                                                             Description)                            CR9025
                                                                                                                                                                                                         PR915
                                                                                                                                                                                                             PR930
                                                                                                                                                                                                                 PR905
                                                                                                                                                                                                                     KW10

                                                 M     22
                                                             W 0.05
                                                                              GMM 8030-080MW GMM 8030-08 8.0 0.8 6.0
                                                 L                            GMG 8030-050MG GMG 8030-05MG 8.0 0.5 6.0

Chip Control Oriented /                                H
          M Class

                                           W 0.03   L                                                                                                                                                                               KIGM U  8                                      G59
                                                22                                                                                                                                                                                  KIGMU   8

Sharp-Cutting Oriented / Precision Class 15                   M
        Ground Chipbreaker                                                 H

                                             M            W 0.02

                           L GMGA 8030-400R GMGA 8030-40R 8.0 4.0 6.0H

 Sharp-Cutting Oriented /                                                                                                                                                                                                                                                          G93
     Precision Class
     Full-R / Copying

                                                                                                For recommended cutting conditions, see page

If using a full-R insert with KIGM-8 type toolholder, you need to modify the corner of insert adapter of toolholder.

: Std. Item  : Check Availability R : Std. Item (R-hand Only) L : Std. Item (L-hand Only)                                                                                                                                            Inserts are sold
                                            для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru                                                                                                                              in 10 piece boxes.
                                                                                                                                                                                                                                                                                                  G59