Kyocera - Основной каталог 2011-2012 ENG
System Tip-Bar для заказа - kyocera@kyocera-tools.ru
SVN-N (without side stopper) SVNS-N (without side stopper / without setscrew)
L2
Note 2 F1 L2 H1 B F2 H1 B
F1
Note 1 L1 F3 1
Setscrew (SP34) L4 L3 L1
h
h
Fig.1 (SVN-N) Fig.2 (SVNS-N)
Right-hand shown R-hand Insert for R-hand Toolholder.
Note 1 & Note 2 : For insert dimensions, see page F14~F15
Toolholder Dimensions
Dimension (mm) Spare Parts Applicable Inserts
F Drawing Clamp Screw Wrench Setscrew F14~F15
Description Std. H1=h B L1 L2 L3 L4 F1 F2 F3 FT G43
G64
J27
LTW
SVNR 1010H -12N 10 10 100 10 VNBR -
1212K -12N 12 12 12 VNBTR -
Boring 1616K -12N 16 16 125 22 - - 16 - - Fig.1 SB-3080TR FT-10 SP3 4 VNGR -
2020K -12N 20 20 20 VNFGR -
2525M -12N 25 25 150 25 VNTR -
SVNSR 1010K-12-06N 10 10 125 10 12 10 29 6 (VNBR 06- )*
(VNBR 11- )*
1 0 1 0 K -12-11N 10 10 125 10 12 10 33 11 (VNBTR
(VNGR 11- )*
(VNTR -11)*
-11)*
1212M -12-06N 12 12 150 10 12 12 29 6 (VNBR 06- )*
1212M -12-11N
(VNBR 11- )*
1212M -12-20N
12 12 150 10 12 12 33 11 (VNBTR 11- )*
(VNGR -11)*
(VNTR -11)*
45 Fig.2 SB-3080TR LTW-10S - (VNBR 20- )*
12 12 150 10 13 12 42 20 (VNBTR 20- )*
(VNGR -20)*
1616M -12-06N 16 16 150 16 12 16 29 6 (VNBR 06- )*
1616M -12-11N (VNBR 11- )*
16 16 150 16 12 16 33 11 (VNBTR
(VNGR 11- )*
1616M -12-20N 16 16 150 16 13 16 42 20 (VNTR -11)*
(VNBR
(VNBTR -11)*
(VNGR 20- )*
20- )*
-20)*
1. SVN-N (without side stopper) retains high index accuracy by simple restraint.
2. SVN-N (without side stopper) has a setscrew SP3X4. Changing the setscrew SP3X4 to a screw HS3X4 (sold separately) enables the holder
to be used as a binding effect holder similar to the side stopper holder.
3. Please use [SVN / SVNS inserts] with side stoppers if machining with binding effect is required (e.g. varying directions for internal,
external or face cutting when using only one tool).
All System Tip-Bar Inserts are used with a SVNSR-N Toolholder, however, When setting the cutting edge at the face level of the toolholder as shown in Fig.2, use the insert shown in ( ).
In these cases, the F3 dimension of the toolholder corresponds to the L2 dimension of the insert.
Spare Parts (Optional)
Screw Wrench
(Side Stopper)
HS34 LW-1.5
: Std. Item : Check Availability
F16 для заказа - kyocera@kyoera-tools.ru www.kyocera-tools.ru